Explore the separate displacer and power cylinders of a gamma Stirling engine. Adjust crank radii, bore, speed and phase to see their motion, then calculate power-piston stroke, swept volume and cycle timing.
Stirling Engine Gamma Interactive Calculator
Vary power-piston bore, crank radii, speed and phase in a gamma layout. The calculator reports direct geometry and cycle timing, not thermodynamic or brake power.
Equation Used
- Bore is the sealed power-piston bore.
- Crank radii set ideal geometric strokes.
- Separate displacer and power cylinders are linked by an open gas passage.
- No power, efficiency, pressure, stress, leakage or heat-transfer adequacy is predicted.
Change displacer lead to compare timing in the animation. The four numerical outputs describe power-piston geometry and shaft timing; they do not predict engine power.
How the Gamma Layout Works
The displacer moves working gas between hot and cold spaces. A separate sealed power piston responds to the changing gas pressure and connects to the crankshaft. A passage joins the two cylinders. The gamma arrangement is shown in Figure 2-1 of JPL Publication 84-30.
In this illustration, each stem stays on its cylinder axis and connects to an external slider-crank. The crank radii set travel, while the displacer-lead slider changes the relative phase. The drawing shows coordinated motion; it does not solve gas pressure, temperature or heat flow.
Using This Calculator
Use the tool to compare a proposed power-piston bore and stroke, or to explain why two cranks can turn together while their pistons reach the ends of travel at different times. It is also useful for checking the conversion between RPM, revolutions per second and cycle period.
Generator selection, heater sizing and fuel consumption require a thermodynamic model and measured operating data. The NASA-hosted Stirling-cycle analysis explains why phase, temperatures, volume ratios and dead spaces matter, and why ideal cycle results are not direct predictions of real engine power.
Stroke, Swept Volume and Timing
Vs = (πD²/4)s
f = N/60
T = 60/N
Here D is power-piston bore, rp is power-crank radius, s is stroke, N is RPM, f is revolutions per second and T is seconds per revolution. With D and s in millimetres, divide the calculated volume by 1,000 to display cubic centimetres.
The displacer crank radius and lead affect the animation but do not appear in these four equations. Their effects on pressure or power require information beyond this calculator.
Worked Geometry and Timing Example
For an 80 mm power-piston bore, 25 mm power-crank radius and 1,000 RPM:
- Stroke is 2 × 25 = 50 mm.
- Swept volume is (π × 80²/4) × 50 = 251,327 mm³, or about 251.3 cm³.
- Shaft speed is 1,000/60 = 16.67 revolutions per second.
- Cycle period is 60/1,000 = 0.060 seconds.
Increasing the bore changes swept volume but leaves stroke and timing unchanged. Increasing power-crank radius changes both stroke and swept volume. Increasing RPM changes frequency and period; it does not change the geometric volume.
Layout and Model Limits
Alpha arrangements use two power pistons. Beta arrangements place a power piston and displacer in one cylinder; gamma arrangements separate them into two cylinders. These are layout distinctions, not universal rankings of efficiency or service life.
The numerical results here are geometric identities and speed conversions. They do not specify working-gas pressure, heater temperature, seal clearances or a safe operating speed. Real performance depends on heat exchange, regeneration, dead volume, leakage and mechanical losses; no fixed percentage correction can be selected from this tool.
Frequently Asked Questions
Why does changing displacer lead leave the numerical results unchanged?
Lead changes the relative motion shown by the animation. The displayed results use only power-piston bore, power-crank radius and RPM; they do not calculate thermodynamic work.
What does the displacer crank-radius slider change?
It changes the illustrated displacer travel. It does not change power-piston bore or crank radius, so it does not change the displayed power swept volume.
Is swept volume the total gas volume?
No. It is the volume swept by the power piston. Clearance spaces, the displacer cylinder, connecting passages and heat exchangers are not included.
Does the speed slider predict how fast an engine will run?
No. RPM is an entered condition. The tool converts it to shaft frequency and cycle period.
Does the phase slider identify the best lead angle?
No. It lets you compare relative motion. An optimum for a real engine depends on its thermal and mechanical design.
Can the calculator size a generator or prescribe startup conditions?
No. It does not calculate shaft power, pressure, temperature or operating limits. Use the specific engine design and its documented operating procedure for those decisions.
References
Building or designing a mechanism like this?
Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.