Rhombic Drive Mechanism: How Philips' Counter-Rotating Stirling Linkage Works, Diagram & Uses

← Back to Engineering Library

A symmetric rhombic drive couples two coaxial reciprocating members to two equal, geared crankshafts that turn in opposite directions. Four equal links form the moving rhombus. The geometry constrains the upper and lower joints to the cylinder axis while the paired gears synchronize the cranks.

Rhombic Drive Interactive Calculator

Enter crank radius, shaft spacing, link length and shaft speed to calculate rhombus height limits and angular speed.

0°

Crank Diameter
--
Minimum Rhombus Height
--
Maximum Rhombus Height
--
Shaft Angular Speed
--

Equation Used

h = e − r cos φ; H = 2√(L²−h²); H_min = 2√[L²−(e+r)²]; H_max = 2√[L²−(e−r)²].
Ideal planar geometry and shaft-speed conversion only. No swept volume, phase, force, balance, stress, thermodynamics, efficiency or rating is calculated.
  • The mechanism is planar and symmetric about the cylinder centerline.
  • Both crank radii and all four link lengths are equal; meshing gears impose equal and opposite shaft angles.
  • The selected ranges maintain L > e + r, so the linkage closes throughout one revolution.
  • Clearance, guide loads, elasticity, friction, masses, balance, gas forces, torque, stress and ratings are excluded.

The secondary figure uses the same equal crank radii, fixed crank centers, four equal links and counter-rotating geared shafts.

Watch the Rhombic Drive in motion
Video: Rhombic drive for beta Stirling engines by Nguyen Duc Thang (thang010146) on YouTube. Used here to complement the diagram below.
Same mechanism and inputs as the interactive calculator.

How the symmetric rhombic drive works

Two equal gears rotate oppositely about fixed centers. Equal crank radii place the left and right crank pins symmetrically about the cylinder axis. Two equal upper links meet at an upper crosshead, and two equal lower links meet at a lower crosshead.

In the selected planar geometry the crank pins have the same vertical coordinate and remain mirror images. The two crosshead joints therefore remain on the centerline. A real Stirling machine may connect those joints to a power piston and a displacer through coaxial rods.

What this calculator demonstrates

Select crank radius, crank-center half-spacing, equal link length and shaft speed. The calculator returns crank diameter, the exact minimum and maximum vertical height of the four-link rhombus, and shaft angular speed.

It does not calculate piston swept volume, phase relationship, gas pressure, thermodynamic output, torque, bearing load, stress, friction, balance, vibration, efficiency, life or safe operating speed.

Symmetric linkage geometry

Let r be crank radius, e the horizontal distance from the centerline to either crankshaft center, and L the length of each of the four equal links. At crank angle φ, the half-width between crank pins is h = e − r cos φ and the half-height of the rhombus is q = √(L² − h²).

The full rhombus height is H = 2q. Because e > r in the selected range, Hmax = 2√[L² − (e−r)²] and Hmin = 2√[L² − (e+r)²]. Crank diameter is 2r and angular speed is ω = 2πn/60.

Worked example

For r = 25 mm, e = 50 mm and L = 125 mm, crank diameter is 50 mm. Rhombus height varies from 200.00 mm to about 244.95 mm. At 900 rpm, shaft angular speed is about 94.25 rad/s.

These are linkage-geometry and shaft-speed results only; they are not engine performance or component ratings.

Rhombus height and piston motion

The height H is the distance between the upper and lower linkage joints. It is not the stroke of either joint: both joints also move with the vertical position of the crank pins. Use the animation to see that combined motion.

A Stirling engine can use coaxial rods to connect these motions to its power piston and displacer. Engine output also depends on gas pressure, temperature, cylinder dimensions and losses; the geometry outputs here do not determine power or efficiency.

The two circular shaft symbols indicate synchronized rotation. Their drawn diameters are illustrative and do not represent meshing tooth profiles. The animation is slowed for viewing.

Questions

Why do the crankshafts rotate in opposite directions?

The equal meshing gears synchronize their speeds and reverse direction, maintaining the mirror-symmetric crank-pin positions used by the linkage.

Does centerline motion prove zero side load?

No. The ideal geometry constrains the selected joints to the centerline, but actual side forces depend on guides, deflection, tolerances, friction, loads and construction.

Does this calculator predict dynamic balance?

No. Balance requires all reciprocating and rotating masses, their locations and counterweights. The outputs describe linkage dimensions and shaft speed.

Why must L exceed e + r?

At the widest crank-pin separation, each link must still have a real vertical projection. The selected input ranges always satisfy that closure condition.

Primary technical references

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: