Ross patent US 4,138,897 documents a two-piston Stirling-engine linkage with parallel cylinders, one crankpin, a rigid yoke and a frame-pivoted rocking lever. The yoke's two remaining pivots connect to the piston rods and move approximately in straight lines with a phase relationship set by the complete linkage geometry.
Ross Yoke Linkage Topology Visual
Inspect the source-supported crankpin, rigid-yoke, rocking-lever and two-piston-link topology without assigning unsupported design outputs.
Equation Used
- Connectivity follows US 4,138,897.
- Displayed links and the yoke remain rigid through the illustrative cycle.
- The displayed cylinder axes are parallel and fixed.
- Dimensions, loads, pressure, inertia, bearings, clearances, friction, balance and performance are unspecified.
The visual uses illustrative normalized proportions and is not a drawing for a particular engine.
Patent-supported topology
The crankshaft's single throw carries one apex of a rigid yoke. A rocking lever joins a point on the yoke's opposite edge to a fixed frame pivot, constraining the yoke as the crank turns. The yoke's other two pivots connect through links to pistons in parallel cylinders.
The crank circle and rocking-lever arc together determine the yoke pose. Consequently, piston positions, strokes and phase are outputs of all relevant pivot coordinates and link lengths; they are not independent sliders.
What the visual demonstrates
The visual highlights four source-supported groups: the single crankpin, rigid yoke, frame-pivoted rocking lever and two piston links aligned with parallel cylinder axes. Its proportions are illustrative and internally constrained so the displayed bodies remain rigid.
Ross's patent describes the piston-connection points as moving approximately linearly with a phase relationship appropriate for a Stirling-cycle machine. It does not make their motion exactly sinusoidal.
No universal Ross-yoke calculator is supported
The removed calculator assumed crank radius equals half the selected piston stroke, assigned exact sine waves to both pistons, and let the user enter phase and rod deviation independently. That is not the kinematics of a geometry-constrained Ross yoke.
A quantitative model must specify the crank radius, fixed frame pivot, rocking-lever length, yoke pivot coordinates, piston-link lengths and cylinder-axis locations, then solve the closed-loop constraints through a full revolution. The available page did not define that design geometry, so numerical outputs are removed.
Reading the topology visual
Use the cycle control to follow one illustrative crank revolution while the highlighted component group changes. The crankpin follows a circle, the rocking lever keeps a constant distance from its frame pivot, and the yoke remains a rigid triangle.
The two piston links terminate on fixed parallel axes. This demonstrates connectivity and constraint structure, not dimensions for a particular engine.
Correction boundary
The former article presented exact sinusoidal piston equations, a universal stroke-to-crank-radius identity, user-entered phase and deviation, and numerous power, tolerance, speed, seal-life, failure and application claims without a fully specified linkage or supporting source.
Those claims, the fabricated worked example and the unrelated video are removed. This visual does not predict loads, balance, friction, power, efficiency, durability, clearances or manufacturability.
Questions
Are Ross-yoke piston motions exact sine waves?
No. The patent describes approximately linear piston-connection motion. The actual displacement curves depend on the complete linkage geometry.
Does piston stroke always equal twice the crank radius?
No universal identity follows for this multi-link mechanism. Stroke can differ from crank-throw diameter and must be solved from a specified geometry.
Can phase be selected independently?
No. In a physical linkage the relative timing of the two piston motions emerges from the shared crank, yoke, rocking lever and pivot locations.
Does the visual prove low side load or dynamic balance?
No. It identifies topology only; force and balance claims require mass, inertia, pressure, bearing, guide and dimensional data.
Primary and technical references
- US 4,138,897, Balanced crankshaft mechanism for the two piston Stirling engine — Ross's primary patent describing the single crankpin, yoke, rocking lever, parallel cylinders and approximately linear piston-connection motion.
- Andy Ross, Making Stirling Engines — inventor's account of the yoke drive and its combination of crankpin circular motion with a rocking-lever arc.
- US 5,146,749, Balancing technique for Ross-type Stirling and other machines — later patent restating the basic Ross-type crank, yoke, swinglink and piston-link arrangement while addressing balancing separately.
Building or designing a mechanism like this?
Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.