Cam Between Yoke Friction-rollers (valve) Mechanism Explained: How It Works, Parts, Diagram & Uses

← Back to Engineering Library

An irregular rotating cam can drive a guided yoke through two opposed rollers. Hiscox illustrates this arrangement for valve-rod motion. The interactive construction below keeps the roller contacts consistent when their centre spacing matches the chosen cam pitch geometry.

Cam Between Yoke Friction Rollers Valve Interactive Calculator

Compare the nominal roller-centre span B with the set centre span G. Change the comparison allowance and speed. The diagram shows matched contact, clearance or interference; these dimensions are not clear surface gaps.

0°

Gap Error
--
Allowance margin
--
Allowance used
--
Cycle Time
--

Equation Used

Centre-span error = G−B; allowance margin = T−|G−B|; allowance used = 100|G−B|/T; cycle period = 60/N.
B and G are distances between opposing roller centres. The illustrative roller radius is 0.08B. The profile is generated from r(ψ)=B[0.5+0.06cosψ+0.015cos(3ψ)], with the cam surface offset inward along the pitch-curve normal by the roller radius. Opposite pitch radii sum to B. An allowance comparison cannot make interfering rigid parts fit.
  • Fixed camshaft and a vertically guided rigid yoke; two equal circular rollers.
  • The chosen pitch curve is an explanatory construction, not a recovered historical manufacturing profile.
  • At G=B both rollers contact. For G>B the illustrated upper contact is retained and lower clearance is shown; the model does not solve free motion in that clearance.
  • For G<B the drawing is an interference preview. It must not be interpreted as an operable assembly, even if the numerical error is within the entered allowance.
  • Speed sets actual revolution period. Animation is slowed for visual inspection; loads, contact stress, bearing life and valve timing are not calculated.

Compare the set and nominal roller-centre spans. Matching spans allow both rollers to follow the constructed cam profile; excess span shows clearance and insufficient span shows interference. The entered comparison allowance does not override physical contact geometry.

Same mechanism and inputs as the interactive calculator.

A cam enclosed by a guided roller yoke

Hiscox figure 1093 shows an irregular cam between rollers attached to a translating yoke. The yoke carries the valve rod, while the camshaft stays fixed. Opposed contacts can drive the rod in both directions.

The two roller contacts must agree with one rigid centre spacing throughout rotation. This illustration starts with a roller-centre pitch curve whose opposite radii add to B, then offsets inward by roller radius to construct the cam surface.

Examining positive cam drive

The historical reference identifies an old steam-engine valve-gear arrangement. This demonstrator examines its opposed-roller principle. It does not specify a real valve event, load or manufacturing tolerance.

Span comparison and profile construction

The calculation compares set centre spacing G with nominal pitch span B: error=G−B. For a chosen symmetric allowance ±T, the arithmetic margin is T−|error| and allowance usage is 100|error|/T.

The illustrative pitch radius is r(ψ)=B[0.5+0.06cosψ+0.015cos(3ψ)]. Its opposite radius at ψ+180° gives a sum of B. Subtracting the roller radius along the outward normal produces the cam surface. This normal offset is essential; simply subtracting radius radially does not generally give correct roller contact.

These are roller-centre dimensions. A clear surface gap would be smaller by two roller radii. Actual cycle period is 60/N seconds at N rpm.

Try matched spacing and a mismatch

At B=40 mm and G=40 mm, the two roller contacts agree through a full turn. With a comparison allowance of ±0.05 mm, the margin is 0.05 mm. At 300 rpm, the actual period is 0.2 seconds, although the animation is deliberately slower.

Increasing G produces lower-roller clearance. Decreasing G produces overlap in the preview: a rigid assembly cannot occupy that geometry. Even an overlap smaller than the chosen allowance remains physical interference.

What a span check cannot establish

The model distinguishes arithmetic allowance from physical contact. It omits bearing deflection, thermal changes, profile errors, lubrication, forces and wear. A complete mechanism design also needs its intended motion law and operating loads.

Questions about the yoke

Are B and G measured between roller surfaces?

No. They are centre-to-centre spans in this construction.

Why is the lower roller shown inside the cam?

G is too small. The overlap is a geometry warning, not a valid running position.

Can a positive allowance margin guarantee a fit?

No. It only means the numerical span error is within the entered comparison band.

Why is animation slower than the stated speed?

The actual period is calculated from rpm; playback is slowed to keep the contacts visible.

Construction reference

Gardner D. Hiscox, Mechanical Movements, Powers, Devices and Appliances, page 270, figure 1093: irregular cam acting between two rollers in a guided yoke. The analytic contour here is an explicitly stated illustrative construction.

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: