Beta Stirling Engine: Animation and Geometry Calculator | FIRGELLI

← Back to Engineering Library

A beta Stirling engine places a displacer and a sealed power piston in the same cylinder. The displacer moves working gas between hot and cold spaces; the power piston responds to the gas-pressure cycle. Explore the relative phase and crank geometry below. The calculator gives the two strokes and power-piston swept volume, without predicting engine power or efficiency.

Stirling Engine Beta Interactive Calculator

Explore the phase and crank geometry of a beta layout. The calculator reports the two strokes and the power-piston swept volume; it does not estimate pressure, work, power or efficiency.

0°

Power stroke
--
Displacer stroke
--
Power swept volume
--
Displacer lead
--

Equation Used

stroke = 2r; power swept volume = (πD²/4)(2rp).
These are direct geometric quantities. A thermodynamic prediction additionally requires temperatures, charge, dead and exchanger volumes, regenerator behavior and a consistent pressure solution.
  • Bore is the sealed power-piston bore.
  • Crank radii set ideal geometric strokes.
  • The displacer rod passes through a shown sealed gland in the power piston; the connecting rods are drawn at fixed length.
  • No power, efficiency, pressure, stress, leakage or heat-transfer adequacy is predicted.

Change the crank radii to compare strokes, and change the power-piston bore to compare swept volume. Displacer lead changes the relative timing shown in the animation.

Watch the Stirling Engine Beta in motion
Video: Rhombic drive for beta Stirling engines by Nguyen Duc Thang (thang010146) on YouTube. Used here to complement the diagram below.
Same mechanism and inputs as the interactive calculator.

How the beta arrangement works

The displacer and power piston share a cylinder but have different roles. The displacer directs gas between the hot and cold spaces. The sealed power piston changes the total gas volume and exchanges work with the external drive.

The gas path includes heating, cooling and regenerative heat exchange. As gas moves toward the cold space, the regenerator can store heat; it returns that heat during the opposite flow. The amount transferred is not calculated in this geometry model.

Reading the cutaway

  • Displacer: the upper moving member shifts gas between spaces.
  • Power piston: the lower sealed member provides the bore and stroke used for the swept-volume calculation.
  • Nested stem and gland: the displacer stem passes through a sealed opening in the power piston.
  • External linkage: crossheads and fixed-length connecting rods connect the axial stems to synchronized crank planes.
  • Displacer lead: sets the relative phase between the two motions.

This is a motion illustration, not a pressure solution. Turning the drawing forward or backward does not establish whether a real engine would produce work in that direction.

What the geometry model helps explain

The shared-cylinder arrangement is useful for studying the relationship between displacer motion, power-piston motion and swept volume. The two crank radii can be varied separately, so a change in displacer stroke need not change the power-piston stroke.

Heat-engine applications require more than these dimensions. The model does not identify commercial engine layouts, select fuels, set gas-charge pressures, or predict the output of a power or cooling system.

Stroke and swept-volume equations

Power stroke Sp = 2rp. Displacer stroke Sd = 2rd. Power-piston swept volume Vp = (πD²/4)Sp.

D is the power-piston bore, rp the power-crank radius and rd the displacer-crank radius. With all dimensions in millimetres, the calculated volume is divided by 1,000 to display cubic centimetres. The phase output repeats the selected displacer lead.

Swept volume is the volume covered by the power piston’s stroke. It is not total gas volume, clearance volume or work per cycle. Temperatures, charge, heat-exchanger volumes and losses are not inputs.

Worked example: independent crank dimensions

Consider illustrative dimensions of 60 mm power-piston bore, 15 mm power-crank radius and 20 mm displacer-crank radius, with a 90° displacer lead.

  1. Power stroke = 2 × 15 = 30 mm.
  2. Displacer stroke = 2 × 20 = 40 mm.
  3. Power swept volume = (π × 60²/4) × 30/1,000 ≈ 84.82 cm³.

Increasing only the displacer radius to 25 mm makes its stroke 50 mm and leaves power swept volume unchanged. Increasing only the bore to 70 mm gives about 115.45 cm³. Changing lead alters relative timing, without changing either geometric stroke.

Comparing the Stirling layouts

Layout Arrangement
Beta Displacer and sealed power piston share a cylinder.
Alpha Two sealed power pistons occupy separate hot and cold cylinders.
Gamma A displacer cylinder connects to a separate power-piston cylinder.

The distinction is geometric. Actual output, service life, noise and cost depend on a complete design and operating conditions. The shared cylinder alone does not establish an efficiency or power advantage.

Frequently asked questions

What distinguishes the displacer from the power piston?

The displacer directs gas between hot and cold spaces. The sealed power piston changes total gas volume and exchanges work with the drive. The calculator’s bore input belongs to the power piston.

Why does changing the displacer crank not change power swept volume?

The power-volume equation uses power-piston bore and power stroke only. The displacer radius sets its own stroke, which is reported separately.

Does the phase slider change stroke?

No. It changes relative timing. Each ideal geometric stroke remains twice its corresponding crank radius.

Is this a rhombic-drive drawing?

The interactive cutaway uses synchronized inline crank planes with external connecting rods and crossheads. The supplementary video shows a rhombic-drive arrangement for comparison.

Can these dimensions predict shaft power?

No. A thermodynamic prediction needs temperatures, gas charge, working and dead volumes, heat transfer and losses. Swept volume alone is not a power calculation.

Can the animation prove that the engine will run in either direction?

No. It illustrates imposed motion. The relationship between heat flow, gas pressure and mechanical work must be evaluated to establish an operating direction.

Does the calculator specify piston clearances or pressure ratings?

No. The inputs describe ideal motion and power-piston swept volume. They do not establish thermal clearances, stresses, seal suitability or operating-pressure limits.

References

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: