A flexible curve is a bendable drawing guide that can retain a chosen shape while you trace its edge. It lets you draw a custom contour without selecting a fixed template. The calculator below compares an ideal elastic core with an entered reference radius; it does not predict how a real curve retains its shape or begins to kink.
Flexible Curve Scriber Interactive Calculator
Compare ideal elastic bending moment, circular section geometry and an entered reference radius. Actual shape retention and damage depend on the construction.
Equation Used
For an ideal linear-elastic circular core, M = E I / R and I = pi d^4 / 64. This calculates an elastic moment at the entered curvature, not the force needed to reshape an actual drawing guide. Plastic deformation, sheath forces and residual curvature are not modeled.
- Core is treated as a circular equivalent beam.
- The moment comparison assumes linear-elastic bending with constant local curvature.
- E is the core material modulus and sheath springback is not included.
- The radius percentage is 100 times reference radius divided by bend radius, capped at 100%. It is not a probability of damage.
How the drawing guide holds a curve
The tool bends along its length and provides an edge for a pencil to follow. A shape-retaining core supports the contour; a surrounding jacket supplies the drawing surface. The cross-section shows one lead-core construction, rather than a specification for every flexible curve.
Set the curve against the points or profile you want to reproduce, then hold it steady while tracing. Its shape is chosen by the user. Unlike a compass, it does not automatically generate a circular arc, and unlike a fixed French curve it can be reshaped.
Product construction determines permissible bending and handling. Use the instructions for the actual tool rather than treating an entered reference radius as a verified limit.
Drawing and transferring contours
A flexible curve can help draw a one-off contour on paper or transfer a profile to a pattern. The same guide may be reshaped for successive curves.
Check the traced line against the intended points and tangents. Tool movement, pencil position and local irregularities can affect the result. The calculator does not estimate tracing accuracy or guarantee that a contour remains unchanged when the guide is lifted.
Ideal elastic bending comparison
The tool assumes a circular equivalent core with diameter d. Its second moment of area is I = πd⁴/64. For linear-elastic bending, moment is M = EI/R, where E is Young’s modulus and R is local bend radius.
With E entered in GPa and d and R in millimetres, I is in mm⁴ and the displayed moment in N·m equals E × I / R numerically. Doubling diameter multiplies I and this ideal moment by 16; doubling radius halves the moment.
A malleable core that keeps a permanent bend is not described by elastic stiffness alone. Yield behavior, composite construction and loading history are absent, so the result does not establish shape retention, a kink threshold or required hand force.
The other outputs are radius difference R − Rmin and min(100, 100Rmin/R). Rmin is an entered reference value. The capped ratio is a comparison, not a damage probability.
Example: changing an ideal core’s bend radius
Enter E = 16 GPa, equivalent diameter d = 3 mm, bend radius R = 80 mm and reference radius Rmin = 25 mm. These are illustrative inputs, not ratings for a commercial drawing guide.
The circular section has I = 3.9761 mm⁴. The elastic comparison gives M = 16 × 3.9761 / 80 = 0.7952 N·m. Radius difference is 55 mm and capped radius ratio is 31.25%.
Increasing R to 160 mm halves the moment to 0.3976 N·m. It does not tell you whether a real core will spring back or hold either curve; that requires its material and construction behavior.
Choosing a drawing method
A flexible curve offers a reshaped edge for an individual contour. A French curve provides fixed profiles that can be matched to portions of a line. A drafting spline bends between supports or weights, with its shape influenced by their placement.
Choose according to the contour, scale and required repeatability. No single accuracy, minimum radius or service life applies to every tool. Inspect the actual drawing edge and check the finished line against the job’s reference geometry.
Frequently asked questions
Does the moment result predict whether the tool keeps its shape?
No. It assumes a linear-elastic circular core. Permanent set and springback require material and construction information that this calculator does not use.
What does Capped radius ratio mean?
It is 100 times entered reference radius divided by bend radius, limited to 100%. It is not a likelihood of kinking.
Where should the reference radius come from?
Use applicable instructions for the actual tool if you want a product-specific comparison. An illustrative value entered here does not become a verified limit.
Why is diameter so influential?
The circular second moment of area varies with diameter to the fourth power. Doubling diameter multiplies the ideal elastic bending moment by 16 at the same modulus and radius.
Can the calculator use a rectangular core directly?
No. Its section formula is circular. A rectangular or composite core needs an appropriate section and material model.
Does the tool calculate drawing accuracy?
No. It does not model edge condition, pencil offset or motion while tracing. Check the drawn contour against the required points and tangents.
Further reading
Building or designing a mechanism like this?
Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.