Ellipsograph Turntable Mechanism: How It Works, Parts, Formula and Diagram Explained

← Back to Engineering Library

An ellipsograph uses constrained motion to trace an ellipse. The illustrated instrument has a rigid extended arm with pins in perpendicular guides on a round base. The calculator compares guide clearance and load-scaled measured deflection, with a magnified fit inset beside the ideal tracing geometry.

Ellipsograph Turntable Interactive Calculator

Inspect an extended-arm ellipsograph and magnified guide fit. Compare signed pin clearance and load-scaled measured deflection without treating their sum as proven pen accuracy.

0°

Signed guide clearance
--
Positive gap comparison
--
Scaled measured deflection
--
Combined scalar comparison
--

Equation Used

c=W−D; δ=δ200·F/200; scalar comparison=c+δ only when c≥0.
Negative clearance is interference. Linear load scaling assumes the same measured configuration and response regime.
  • Parallel ideal slot walls and a centered round pin.
  • The same entered fit is shown for both guide pins.
  • Measured deflection scales linearly with load.
  • Fixed illustrative 120 by 60 mm semi-axis geometry.

Pin diameter, slot width, pen load and measured deflection are the four comparison inputs. The combined scalar comparison is not a validated pen-position error bound.

Same mechanism and inputs as the interactive calculator.

An extended arm follows perpendicular guides

The base stays at a fixed orientation during the demonstration. Horizontal pin H and vertical pin V are 60 mm apart. The tracing point is 60 mm beyond H, making its distance from V 120 mm. Their connected motion generates an ideal ellipse with horizontal semi-axis 120 mm and vertical semi-axis 60 mm.

The main drawing is a plan-view geometry preview. Its green curve is the projected ideal path. The pin diameter and slot width use the same drawing scale; the larger inset makes their fit easier to inspect. A single clearance value does not define a pen-error trajectory, so the trace shows ideal geometry.

The round base is not given an additional independent rotation. Rotating the whole instrument would change its orientation on the work, which is a separate operation. The depicted fixed dimensions are an example, not measurements of the cited museum instrument.

Compare guide fit and measured compliance

The four controls are: pin diameter, slot width, pen load and a measured deflection under a reference load. The first pair compares geometric fit. The second pair scales a measured deflection under an assumed linear load response.

A historical ellipsograph can use adjustable slider positions to change its ellipse. This example compares fit and compliance; it does not predict the instrument’s overall accuracy. The Smithsonian example provides a real instrument reference for the extended-arm arrangement.

Separate clearance from deflection

Signed total clearance is c=W−D, where W is slot width and D is pin diameter. For a centered pin, positive per-side gap is c/2. Negative c means the pin does not fit the ideal slot, rather than implying a perfect zero-clearance mechanism.

With measured reference deflection δ200 at 200 gram-force, the linear comparison is δ=δ200·F/200, with F also in gram-force. One gram-force is 0.00980665 N. This is a calibrated linear assumption, not a calculation from arm material or section dimensions.

The summed result is c+δ for nonnegative clearance. It is a combined scalar comparison, not total pen error. Guide play is lateral, while deflection under downward pen load can be out of plane. Their scalar sum does not establish a physical displacement vector or a validated error bound.

For the fixed tracing geometry, H=(60 cos θ,0), V=(0,−60 sin θ), and P=(120 cos θ,60 sin θ), in millimetres. Distances HV=60, HP=60 and VP=120 remain constant.

Default fit and load comparison

A 6 mm pin in a 6.15 mm slot has 0.15 mm total clearance, or 0.075 mm on each side when centered. A measured 0.05 mm deflection at 200 gf remains 0.05 mm at the default 200 gf load. The scalar comparison is 0.20 mm.

At 400 gf the assumed linear deflection becomes 0.10 mm. This does not prove that the actual instrument remains linear at that load. If a 12 mm pin is entered with a 3 mm slot, clearance is −9 mm: the page reports interference, preserves a clearly labeled geometry preview and withholds the combined fit allowance.

What a real accuracy assessment also needs

Pen error depends on the complete geometry, guide directions, where play is taken up, pivot fits, mounting and the direction of deflection. Slot clearance alone does not determine pen wander. No universal instrument accuracy, fit class, wear life or required perpendicularity tolerance is inferred here.

A zero-clearance ideal model also says nothing about friction or whether an actual pin can slide freely. The reference deflection should be measured in the same configuration and direction as the comparison. The drawing remains a kinematic illustration rather than a manufacturing drawing.

Ellipsograph fit questions

Why is the sum only a scalar comparison?

The sum does not account for geometry or the directions of guide play and deflection, so it is not a pen-error bound.

What happens if the pin is wider than its slot?

The inset shows interference and the combined allowance is unavailable. The upper animation is explicitly a geometric preview only.

Why does pen load not distort the ellipse?

The inputs do not specify a deformation field or a direction-dependent tracing-error model. The displayed ellipse therefore follows ideal rigid-body geometry.

Does the base rotate during the trace?

Not in this demonstration. The base establishes fixed perpendicular guide directions while the arm moves.

References

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: