Great-Curve Delineator: Arc Radius and Rise Calculator | FIRGELLI

← Back to Engineering Library

A great-curve delineator draws a circular arc using two fixed pins and a pair of straight rails held at a constant angle. The pencil sits at the rail vertex, so the circle’s center can remain outside the drawing area. Enter chord length and half the arc’s central angle to calculate radius, apex rise and the change in rise caused by a small angle increase.

Great Curve Delineator Interactive Calculator

Set a chord and half central angle to define a circular minor arc, then inspect the constant included angle maintained by two ideal rails through fixed endpoint pins.

0°

Arc Radius
--
Apex Rise
--
Arc Angle
--
Apex Error
--

Equation Used

R = L/(2 sin theta); minor central angle = 2 theta; rail included angle on the minor locus = 180 degrees-theta; sagitta = R-sqrt(R^2-(L/2)^2)
Theta is half the minor central angle. The included rail angle is its supplement, 180° − theta. Apex Error compares the original rise with the rise after adding Half-angle Drift to theta.
  • Two fixed point pins define chord L.
  • The pencil vertex lies on the displayed minor circular arc.
  • Two straight ideal rails pass through the vertex and respective pins.
  • No rail thickness/flex, pin diameter/clearance, pencil offset, friction or build-tolerance model.

Theta is half the minor central angle; the rail angle is 180° − theta. Ideal geometry omits pin clearance, rail thickness and flex, pencil offset and construction tolerances.

Same mechanism and inputs as the interactive calculator.

A circle from a constant angle

The two pins define a fixed chord. As the pencil moves, each rail continues through its corresponding pin and the included angle at the pencil stays constant. By the inscribed-angle theorem, the pencil follows a circular arc.

For the minor arc displayed here, the angle at the pencil intercepts the opposite major arc. If θ is half the minor central angle, the rail angle is 180° − θ. Thus the default θ = 30° corresponds to a 60° minor arc and a 150° angle between the two rays from pencil to pins.

Parts and idealizations

The model has two point pins, two zero-thickness straight rails and a pencil at their intersection. It shows the angular geometry, not the usable length of a real frame. A physical tool needs bearing edges that remain in contact, a secure angle setting and a pencil position matched to that geometry.

The drawn motion avoids placing the pencil exactly on either endpoint pin, where one defining ray would have zero length.

Drawing when the center is out of reach

The construction can be useful for a large-radius circular template when a compass center would lie beyond the board or available floor space. It can also illustrate how a constant viewing angle defines a circle.

It draws circular arcs. A fair-looking ship or furniture curve is not necessarily circular, so establish the intended geometry before using a fixed-angle frame to reproduce it. Check the actual chord and rise on a trial pattern; this calculator does not include pin diameter, rail flex or pencil offset.

Circle and rail-angle geometry

Let θ be half the central angle of the displayed minor arc. Its radius is R=L/(2 sin θ), central angle is 2θ and minor sagitta is R−sqrt(R²−(L/2)²).

A pencil vertex on that minor arc sees the opposite major arc. Therefore the included angle between the two rails is 180°−θ, not θ. The two angles describe different parts of the same circle.

Example: chord, arc and angle drift

Use chord L = 10 m, Half Arc Angle θ = 30° and Half-angle Drift = 0.5°.

  1. Radius: 10 / (2 sin 30°) = 10 m.
  2. Minor central angle: 2 × 30° = 60°.
  3. Rail angle at the pencil: 180° − 30° = 150°.
  4. Apex rise: 10 − √(10² − 5²) = 1.339746 m.
  5. At θ = 30.5°, the rise is 1.363156 m, an increase of 23.4 mm.

The Apex Error tile compares the original rise with the rise after increasing θ by the entered drift. The corresponding rail angle decreases by the same amount. The tile is not a plus-or-minus tolerance band.

If a chord and rise are already known, radius can also be found from R = L²/(8h) + h/2. For L = 1.8 m and h = 0.050 m, R = 8.125 m. That is a geometric construction, not a structural check on the resulting template or member.

Scope and limitations

The exact locus follows from point pins and zero-thickness rigid rails. A physical tool has pin diameter and clearance, finite bearing edges, pencil offset, rail flex, setup error and a limited usable sweep. Those effects are not predicted by this ideal geometry.

Frequently asked questions

Is Half Arc Angle the angle between the rails?

No. It is half the minor central angle. The angle between the two rays from pencil to pins is 180° minus that input.

Does Half-angle Drift change the main drawing?

No. It changes only the Apex Error comparison. The main radius, rise and drawing use the original half-angle.

Is Apex Error a plus-or-minus range?

No. It is the absolute rise difference after adding the entered nonnegative drift to the original half-angle. A negative drift would require a separate calculation.

Why does a larger half-angle make the rise greater?

With the chord fixed, a larger half-angle gives a smaller radius and a deeper minor arc.

Does changing chord length affect radius and rise proportionally?

Yes, when the half-angle is held fixed. Radius, rise and the drift-induced rise difference all scale with chord length.

Can the tool draw any curve through three points?

This construction defines a circular arc, not an arbitrary smooth curve. The three points must define the intended circle.

Does the calculation include pencil or pin size?

No. Pins are points, rails have no thickness and the pencil is exactly at the vertex.

References & Further Reading

  • Wikipedia contributors. Inscribed angle theorem. Wikipedia

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: