Trammel for Drawing Ellipses: Semi-axes and Slider Span

← Back to Engineering Library

An ellipse trammel uses two points on a rigid beam constrained to perpendicular straight tracks. A third collinear point on the beam traces an ellipse; its distances from the two slider pivots set the two semi-axis magnitudes.

Trammel for Drawing Ellipses Interactive Calculator

Enter two full ellipse-axis diameters. The calculator sorts them, reports the semi-axes, and gives the ideal coordinate span of each slider; physical track length needs additional hardware clearance.

0°

Sorted semi-major axis
--
Sorted semi-minor axis
--
Ideal X-slider coordinate span
--
Ideal Y-slider coordinate span
--

Equation Used

a=max(D1,D2)/2; b=min(D1,D2)/2; c=a-b; P=(a cos theta,b sin theta); span_x=span_y=2c=|D1-D2|.
For the illustrated arrangement the slider coordinates are ((a-b)cos theta,0) and (0,(b-a)sin theta). Their full coordinate spans are both 2|a-b|. Equal entered axes make c=0 and degenerate the two-slider construction even though the locus equation is a circle.
  • The two tracks are straight, perpendicular and intersect at the ellipse centre.
  • Slider pivots and tracing point are collinear on a rigid beam.
  • The entered values are full orthogonal-axis diameters and are sorted before naming major and minor axes.
  • The ideal slider coordinate span excludes slider length, end stops and operating clearance.
  • Backlash, friction, deformation, tool offset, track width, tolerance and safe fabrication are omitted.
Same mechanism and inputs as the interactive calculator.

Two Perpendicular Sliders on One Beam

Patented trammels use two slider blocks moving in crossed, mutually perpendicular tracks and pivoted to adjustable points on a rigid beam. A drawing, cutting or marking point fixed to that beam is thereby constrained to an elliptical path.

Let the tracing point be P=(a cos theta,b sin theta). In the illustrated collinear arrangement, the horizontal-track slider is at ((a-b)cos theta,0) and the vertical-track slider is at (0,(b-a)sin theta). Both sliders therefore move between plus and minus |a-b|.

What This Calculator Does

The tool sorts two entered full-axis diameters, divides them by two for the semi-major and semi-minor axes, and reports the ideal coordinate span of each slider as the absolute diameter difference.

It does not size a physical track, beam, slider, pivot, cutter or marking tool.

Ideal Trammel Coordinates

a = max(D1,D2)/2
b = min(D1,D2)/2
P = (a cos theta,b sin theta)
Sx = ((a-b)cos theta,0)
Sy = (0,(b-a)sin theta)
spanx = spany = 2|a-b| = |D1-D2|

These are coordinate spans, not finished track lengths. Actual tracks require room for the slider body, end retention and clearance.

Worked Ideal Example

For entered diameters 300 mm and 200 mm, a=150 mm and b=100 mm. The slider separation is 50 mm, and each slider coordinate ranges from -50 mm to +50 mm, giving an ideal span of 100 mm on each track.

The physical track must be longer than 100 mm if the slider has finite size or requires end clearance.

Model Boundary

  • Mechanical arrangement: two adjustable beam pivots carry sliders in perpendicular crossed tracks and constrain a beam-mounted working point to an ellipse.
  • Calculated: sorted semi-axes and ideal slider-coordinate spans.
  • Not calculated: slider-body length, track end geometry, retention, clearance, backlash, perpendicularity error, beam or pin deformation, cutter diameter, tool offset, friction, drive force, speed, acceleration, wear, tolerance, accuracy, material, strength, workpiece restraint or safe operation.

Frequently Asked Questions

Are the displayed slider spans the finished slot lengths?

No. They are only coordinate ranges for ideal point sliders.

Why are both slider spans equal?

Both ideal slider coordinates have amplitude |a-b|, on perpendicular axes.

Why sort the entered diameters?

Major and minor name the larger and smaller orthogonal diameters regardless of entry order.

What happens when both diameters are equal?

The locus equation is a circle, but a=b makes the two slider pivots coincide, so this two-slider construction is degenerate.

Does the calculator include cutter or pencil offset?

No.

Can the output define manufacturing tolerances?

No. A physical design needs complete hardware geometry, loads, tolerances and safety provisions.

References

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: