A geared watch stop limits rotation when arms attached to two meshing wheels meet. Hiscox’s figure 1190 shows this simple contact principle. The animation follows the arms as they approach, touch and separate on reversal. The calculator uses equal gears and matching rounded arms to make the contact geometry explicit.
Geared Watch Stop Interactive Calculator
Choose the equal wheel tooth count, module, arm extension and arm half-width. Calculate the closing angle from an initial position with both arms pointing upward. These are illustrative dimensions, not a watch-calibre specification.
Equation Used
N is the tooth count of each equal gear; m is module in mm. Arm extension e and half-width w are multiples of module. The arms share one plane above the gear faces and have round tips of radius h, centered L from each shaft. Equal gears rotate oppositely through the same angle. The result is first contact in this symmetric approach, not total winding turns, stopping accuracy or load capacity.
The arms provide the stop
The wheels mesh at fixed centers. An arm is fixed to each wheel and turns with it. As the arms approach one another, their clearance decreases. Once they touch, their contact opposes further movement in that direction. Reversing the drive separates them.
Hiscox identifies arm contact as the stopping action in figure 1190. The drawing does not provide a dimensioned gear set, arm profile or initial adjustment. This example uses equal wheels, equal straight arms and rounded ends. Both arms begin pointing upward, then rotate symmetrically toward each other.
The gear teeth remain engaged throughout. The arms sit in a common plane above the gear faces so they can meet without colliding with teeth underneath. The small tip-detail window enlarges the rounded ends near contact and shows “Tips apart” when their separation exceeds the window. The animation pauses at contact before reversing to show the two states clearly. This repeating display sequence is not an automatic reversing function of a watch.
Understanding a mechanical rotation limit
A positive stop sets a boundary to allowed motion. The drive, gears, arms and supports must withstand the resulting load, and the rest of the mechanism determines which motion is being limited.
This illustration helps distinguish a gear-mounted stop from a stop-seconds mechanism. Stop-seconds is used to pause a watch for time setting; this calculator describes the geometry of two arms meeting. It does not model a seconds hand, balance wheel or crown linkage.
Contact between two rounded tips
For N teeth and module m, each gear has pitch radius R = Nm/2. Equal external gears have shaft spacing D = 2R. Let the arm’s shaft-to-tip-center length be L = R + em and its half-width be h = wm.
When each arm has turned by φ from its upward starting position, the left tip center has moved right by L sin φ and the right tip center has moved left by the same amount. The two tip centers remain at the same height. Their separation is D − 2L sin φ.
The rounded ends first touch when that separation equals 2h. Therefore sin φstop = (D − 2h)/(2L) = (R − h)/L. The calculator reports the inverse sine in degrees. Within the entered ranges, the result is between 0° and 90° and the tips remain the closest points on the arms.
The angular tooth pitch is 360°/N. It describes tooth spacing, not the stop’s repeatability: arm profiles, setting, compliance and backlash affect where a real stop settles.
Example: a pair of 20-tooth wheels
Choose N = 20, module m = 0.40 mm, extension e = 2 modules and arm half-width w = 0.5 modules. The pitch radius is 4.00 mm, shaft spacing is 8.00 mm, arm length is 4.80 mm and tip radius is 0.20 mm.
First contact occurs at asin((4.00 − 0.20)/4.80) = 52.34°. Both wheels turn through that angle in opposite directions. Their angular tooth pitch is 18.00°.
Doubling module doubles every entered linear dimension while preserving the angle to contact. Increasing arm extension makes the arms meet sooner. Increasing arm width also reduces the angular travel before contact.
A geometric boundary is not a strength rating
At the limit, additional input torque loads the gears, arm contact and shaft supports. This calculator has no material properties, contact-stress model or drive-torque input, so it does not establish a permissible force or durability.
Unequal tooth counts, different arm shapes or another initial setting change the sequence. Total winding travel requires those details and the connection to the spring barrel. The symmetric example covers one approach to contact only.
Frequently asked questions
What actually stops the wheels?
Contact between the two arms fixed to the wheels. The teeth keep the wheels coupled; no separate blade enters a tooth gap.
Why do both arms move by the same angle?
This example uses equal tooth counts, giving a 1:1 external gear ratio with opposite directions.
Is angular tooth pitch the stop accuracy?
No. Tooth pitch is the angle between successive teeth. Real stop position also depends on arm geometry, adjustment, backlash and deformation.
Does the animation predict the allowed winding turns?
No. It shows one approach from a chosen starting position. A particular winding mechanism needs its actual tooth counts, arm settings and barrel connection.
Why does changing module leave the angle unchanged?
All lengths in this model scale with module, so the ratio (R − h)/L stays constant.
Why does the animation reverse at the stop?
Reversal is part of the repeating illustration. The contact itself prevents further forward motion; it does not automatically reverse the drive.
Mechanism references
Building or designing a mechanism like this?
Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.