A heart-shaped slot, roller stud and pawl give the stop-roller arrangement a sequence of backward and forward motion. Hiscox movement 967 describes one-third revolution backward and two-thirds forward in each completed driving-disc cycle. The calculator totals those movements; the phase timing shown alongside the diagram is illustrative.
Actuator installation checks for Stop Roller Motion Mechanism
In actuator-driven stop roller motion mechanism, the useful calculation is the one that protects alignment. Keep the moving member guided by the machine structure, and let the actuator supply controlled linear force.
When comparing a cylinder to an electric actuator, convert the discussion into stroke, force, speed, duty cycle, and installed length. Matching one specification is not enough.
For moving panels, hatches, guards, and slides, the actuator should not be the only support. Rails, hinges, bearings, or guides should carry side loads so the actuator shaft remains in push-pull service.
- Keep side load out of the actuator rod by guiding the moving member separately.
- Verify pin diameter, clevis width, bracket stiffness, and alignment under load.
- Check that deflection will not change the actuator load path during operation.
For FIRGELLI actuator projects, compare product families through the FIRGELLI actuator families and use the linear actuator replacement finder when replacing an actuator from another manufacturer. The selection should stay tied to real stroke, force, and mounting dimensions.
Stop Roller Motion Interactive Calculator
Enter a positive driving-disc speed and an integer count of completed driver cycles. The calculator totals the source-stated one-third-revolution backward and two-thirds-revolution forward shaft travel.
Equation Used
- k is an integer count of completed driving-disc revolutions.
- N is positive and constant.
- The separate angular-sequence animation uses an illustrative phase allocation; it is not a solved cam profile.
- No velocity, acceleration, torque, pawl load or tooth strength is inferred.
Follow disc D, heart slot B, roller stud C, pin e and pawl G. The separate timing display illustrates the sequence; slot dimensions and phase durations are not specified.
Heart Slot, Roller Stud and Pawl
The illustrated arrangement combines driving disc D, heart-shaped slot B and roller stud C with a notched wheel on shaft F. Back pin e lifts pawl G, allowing the sequence to proceed. Hiscox describes backward travel of one-third revolution and forward travel of two-thirds revolution per completed driver revolution.
The left drawing keeps the slot and roller in a static contact view. The separate angular display makes the backward, stop and forward portions easier to follow. Its phase widths are illustrative because the historical description does not supply a dimensioned slot or the durations of the individual phases.
What to Watch
- Disc D and slot B: the driving member and its heart-shaped track.
- Roller stud C: the contact element in the slot.
- Pin e and pawl G: the pawl-release arrangement.
- Notched wheel and shaft F: the controlled rotating member.
Understanding Stop-and-reverse Sequences
This historical example illustrates a movement that includes both backward and forward rotation rather than a simple forward step. It can help readers distinguish total angular travel from net advance.
The schematic is not a selected packaging indexer, a watch movement or a machine specification. Applying the principle to a new machine would require complete geometry, timing and load analysis.
Completed-cycle Time and Angular Travel
Enter constant driving-disc speed N in rpm and an integer number k of completed revolutions. The calculation uses the per-cycle travels stated in the historical description.
Elapsed time = 60k/N seconds
Backward travel = 120k degrees
Forward travel = 240k degrees
Net forward travel = 240k − 120k = 120k degrees
Backward and forward travel are reported as positive magnitudes. Their signed difference gives net advance. These totals do not determine dwell durations, velocity, acceleration or the shape of the heart slot.
Worked Example: Three Completed Cycles
At 60 rpm, three completed driving-disc revolutions take 60 × 3/60 = 3 seconds.
The accumulated backward travel is 120 × 3 = 360 degrees. Forward travel is 240 × 3 = 720 degrees, giving a net forward advance of 360 degrees.
One net revolution is therefore different from total travel: the output has travelled through 1,080 degrees when both directional distances are added. The calculator does not determine when within each cycle those movements occur.
Travel Totals and Timing
| Quantity | Meaning | Available here? |
|---|---|---|
| Backward and forward travel | Accumulated directional distances over complete cycles | Yes |
| Net advance | Forward travel minus backward travel | Yes |
| Elapsed time | Complete-cycle count divided by constant driver rate | Yes |
| Dwell, velocity and acceleration | How motion is distributed within a cycle | No; a dimensioned motion profile is required |
Increasing driver RPM reduces total elapsed time but does not change travel per completed cycle. No load capacity or safe operating speed follows from these totals.
Frequently Asked Questions
The sequence described for Hiscox movement 967 includes one-third revolution backward and two-thirds forward per completed driving-disc cycle.
Two-thirds forward minus one-third backward gives one-third revolution, or 120 degrees, net forward.
The historical description does not supply the slot dimensions needed to solve continuous roller contact and motion. The contact drawing is separated from the illustrative angular sequence.
No. Phase widths are illustrative; the calculator reports completed-cycle totals only.
No. At the constant speed you enter, it changes elapsed time for the chosen cycle count. The travel totals depend on completed cycles.
No. Contact loads, torque, acceleration, tooth strength and detailed geometry are not calculated.
References
Building or designing a mechanism like this?
Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.