Floating Dredge: Cutter Motion and Slurry-Flow Comparison | FIRGELLI

← Back to Engineering Library

A floating dredge excavates submerged material from a vessel or pontoon platform. In the cutter-suction arrangement illustrated here, a cutter loosens material and a pump carries the resulting water-and-solids mixture through a pipeline. The calculator splits an entered slurry flow into solids and carrier water and compares two entered velocities.

Floating Dredge Interactive Calculator

Compare solids and water volume flow, then compare pipe velocity with an entered reference. This tool does not predict blockage or select a pump.

Solid Flow
--
Carrier Water
--
Velocity Ratio
--
Velocity difference
--

Equation Used

Q_solid = Q_slurry * Cv/100; Q_water = Q_slurry - Q_solid; velocity_margin = v_pipe - v_crit

Solids volume flow equals total slurry flow times the entered solids fraction. Carrier water is the remainder. The velocity readouts compare pipe velocity with an independently entered reference; the tool does not derive a deposition threshold or solve slurry transport.

  • Solids concentration is by volume.
  • The reference velocity must be supplied independently; no particle or transport model calculates it.
  • A positive difference means only that entered pipe velocity exceeds entered reference velocity.
  • No correction is applied for particle size, pipe roughness, or slurry density.
Related dredge footage
Related footage: “Remove Rear Spud & Dredge Pipe,” published by DLAmy on YouTube.
Plan view of a cutter-suction dredge swinging on one spud 123
1 — Planted spud. 2 — Anchor wires. 3 — Cutter at the ladder end. Side winches pull against anchors to swing the vessel about the planted spud. The cutter loosens material at the suction intake. Repositioning for the next cut is a separate operation. Use the interactive animation above to follow the motion.

Cutting, pumping and positioning

The floating platform supports a ladder that positions the cutter and suction intake. The cutter loosens the bed, and a slurry pump moves the mixture into the discharge system.

On the stationary cutter-suction arrangement shown, a working spud provides a pivot while side-anchor wires and winches control the swing. Repositioning the spuds or a spud carriage lets the vessel advance to the next cut. The exact operating sequence depends on the dredger.

The top-view illustration shows this motion concept. It does not calculate excavation forces, winch loads, spud bending or vessel stability.

Choosing an excavation method

Cutter-suction dredgers are used for tasks such as removing submerged sediment and recovering material that can be excavated and transported as slurry. Ground conditions, depth, access and discharge arrangements determine equipment suitability.

Bucket dredges lift material mechanically, while trailing-suction hopper dredgers collect material into a vessel’s hopper. These are distinct arrangements, not interchangeable versions of the simple cutter-suction diagram.

Volume flow and an entered velocity reference

For slurry flow Q and solids concentration Cv in percent by volume, solids volume flow is Qs = Q·Cv/100. Carrier-water flow is Qw = Q − Qs. Both outputs use the same volume-per-time units as Q.

Qs represents solid material volume in the stream, not a bank excavation volume or a loose-pile volume that includes voids. Converting it to in-situ production needs appropriate porosity or density information, which is not an input here.

For pipe velocity v and entered reference vc, the calculator reports 100v/vc percent and v − vc. It does not determine vc from particle size, concentration, pipe diameter or fluid properties. Flow and velocity are independent inputs and are not checked against a pipe area.

Example: splitting a slurry stream

Enter 2,400 m³/h slurry flow and 22% solids by volume. Solid material flow is 528 m³/h and carrier-water flow is 1,872 m³/h.

With entered pipe velocity 4 m/s and reference 3.5 m/s, the ratio is 114.29% and difference is 0.5 m/s. These values compare the two inputs; they do not establish that the pipeline will remain clear.

At 12% solids the solid flow is 288 m³/h; at 32% it is 768 m³/h if total Q remains 2,400 m³/h. The model does not predict whether the pump and pipeline can maintain that flow at either concentration.

What the calculation leaves to the dredging system

Actual production depends on excavation, pump performance, pipeline losses and operating availability. A change in solids concentration can also change the pump and pipeline duty point; keeping Q fixed is an input assumption here.

Use vessel and equipment data for operating limits, site conditions and procedures. This page does not prescribe cutter speed, spud sequencing, booster spacing, suction conditions or blockage-clearing methods.

Frequently asked questions

Is Solid Flow the in-situ excavation rate?

No. It is the solid material volume carried in the slurry. Bank volume also includes the deposit’s voids and needs additional information.

Does Reference velocity come from a sand model?

No. It is entered by the user. The tool has no particle-size or pipe-diameter input.

Does a positive Velocity difference prove the pipe will not block?

No. It only compares two entered velocities. Slurry transport and transient conditions are not modeled.

Why does Carrier Water fall as concentration rises?

At fixed total slurry flow, the solid fraction grows and the remaining water fraction shrinks. Real total flow may also change, but the tool does not predict it.

Are slurry flow and pipe velocity linked automatically?

No. They are independent inputs. Check their consistency with the actual pipe area separately.

Does the swing diagram size spuds or winches?

No. It illustrates the positioning concept and does not calculate structural or line loads.

Manufacturer references

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: