Klondike Mining Machine: Lancaster Washer and Gold Mass Balance | FIRGELLI

← Back to Engineering Library

Hiscox’s “Klondike Mining Machine” is a Lancaster-model placer washer: gravel enters a hopper and a riffle pan vibrated by the pump handle. The pump supplies water, which drains into a settling pan beneath; the historical description includes a fire below it to prevent freezing. The animation here is a general sluice-flow illustration, not that machine. The calculator gives a gold mass balance using an entered recovery percentage.

Klondike Mining Machine Interactive Calculator

Explore contained gold and an entered recovery split. Recovery is an assumption, not a result predicted from the animated trough.

0°

Gold in Feed
--
Assumed Recovered Gold
--
Arithmetic Unrecovered Gold
--
Tailings Grade
--

Equation Used

feed=QG; recovered=eta QG; unrecovered=(1−eta)QG
Entered-recovery mass balance, separate from the illustrative placer-washing animation.
  • Feed grade is uniform over the entered daily volume.
  • Recovery is entered and is not calculated from water flow, riffle geometry, particle size or mineralogy.
  • Tailings volume is treated as equal to feed volume for the displayed grade.
  • No reserve, sampling, density, water-balance or equipment-capacity model.

Tailings grade assumes tailings volume equals feed volume; the moving markers only visualize the entered split.

The historical Lancaster machine

In Hiscox’s entry 1244, the pump handle both operates the water pump and vibrates a riffle pan receiving gravel from a hopper. Water falls from the riffle pan into a settling pan below. The description’s fire beneath the apparatus was intended to keep the water from freezing.

The illustration on this page instead shows a general hopper, screen and sloping sluice. It omits the Lancaster machine’s handle-driven pan motion, pump, lower settling pan and heating arrangement.

Separating gold from placer gravel

Placer washing uses water and gravity to help separate dense gold from gravel and sand. The effectiveness of any apparatus depends on the material and operating conditions. This page does not establish a machine capacity, recovery rate or mineral reserve.

Gold mass balance

For feed volume Q in yd³/day and grade G in g/yd³, contained gold is QG in g/day. At an entered recovery fraction η, assumed recovered gold is ηQG and unrecovered gold is (1−η)QG.

The displayed tailings grade divides unrecovered gold by the original feed volume. It therefore assumes tailings volume equals feed volume; it does not account for screening or changes in bulk density.

Reading the figures and markers

For 1 yd³/day at 2 g/yd³ and an assumed 80% recovery, the feed contains 2 g/day; assumed recovery is 1.6 g/day, leaving 0.4 g/day unrecovered. With equal feed and tailings volumes, the displayed tailings grade is 0.4 g/yd³.

The twelve gold-colored markers provide a coarse illustration of the entered split. Their paths and fixed display speed do not simulate particle settling or equipment throughput.

Recovery assumptions and limits

Recovery is a user input. The tool contains no model of water flow, particle-size distribution, liberation, mineralogy or separation efficiency. Actual results also depend on how representative the entered grade and feed volume are.

The moving illustration is not the Lancaster mechanism described by Hiscox. Neither the drawing nor the mass balance supplies an operating prescription for historical equipment.

Frequently asked questions

Does the animation show Hiscox’s Lancaster machine?

No. It shows a general sluice-flow concept. The historical apparatus used a pump handle to vibrate a riffle pan above a settling pan.

Does changing recovery calculate different particle behavior?

No. It changes the assumed mass split and the selection of illustrative gold markers.

Is the displayed recovered gold a production forecast?

Only as a consequence of the entered feed, grade and recovery assumptions. None of those quantities is predicted or verified by this tool.

How is tailings grade calculated?

Unrecovered gold is divided by the entered feed volume, treating tailings volume as equal to feed volume.

Historical reference

Gardner Dexter Hiscox, Mechanical Movements, Powers, Devices and Appliances, entry 1244: Klondike Mining Machine, Lancaster model.

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: