Arastra Ore Mill Mechanism: How the Drag Stone Gold and Silver Ore Grinder Works

← Back to Engineering Library

An arastra, also spelled arrastra, grinds ore by dragging heavy stones across a circular stone bed. A central rotating sweep pulls the stones through their attachments. The animation shows the drag-stone arrangement, and the calculator gives track distance, speed and lap time from radius and rpm.

Arastra Ore Mill Interactive Calculator

Vary sweep radius and RPM to see the drag stone track speed, lap time, and grinding distance.

0°

Stone Speed
--
Track Length
--
Lap Time
--
Grinding Distance
--

Equation Used

v = 2 * pi * r * RPM / 60

The calculator uses the circular track speed of the drag stone: multiply the sweep circumference by revolutions per minute, then divide by 60 to convert to metres per second.

  • Sweep radius is measured from the central post to the drag stone contact path.
  • RPM is steady and the stone follows a circular track.
  • Linear speed describes the selected circular path; the finite stone footprint and irregular contact motion are not calculated.
The reference drawing uses the selected sweep radius and speed.

A sweep pulling stones around a bed

The central post and sweep rotate together. Chains or other attachments connect the sweep to the drag stones, so the stones trail their attachment points across the fixed bed. Ore between the stones and bed is ground by their contact and motion.

Parts to identify

  • Stone bed: the stationary grinding surface.
  • Central post: the rotational axis supporting the sweep.
  • Sweep arms: carry the attachment points around the axis.
  • Chains: transmit pull to the trailing stones.
  • Drag stones: the heavy grinding members moving over the ore.

The plan view shows two stones for clarity. Historical mills varied in dimensions, stone count and drive arrangement. A drag stone is different from an upright wheel rolling around a pan; the latter belongs to a roller-mill arrangement.

The drawing assumes a circular path. Real contact depends on stone shape, attachment geometry, bed condition and the charge. It does not establish an allowable chain length, post dimension or stone load.

Historical ore preparation

Arrastra remains document one way miners reduced ore before further processing. The National Park Service’s White’s Gulch record describes a stone-flagged circular pit, four granite drag blocks and marks left by dragging stones. Such site records provide evidence of construction without turning one site’s dimensions into a universal design.

Grinding and recovering metal are separate questions. A speed calculation does not predict liberation, throughput or recovery. Historical use of mercury amalgamation also does not make the illustration a present-day mineral-processing procedure.

Surviving beds, stones and wear marks are part of a site’s archaeological evidence. The calculator offers a way to explore the motion without dismantling or reworking the remains.

Circular travel calculation

For sweep radius r in meters and steady rotation N in rpm, Track Length C = 2πr meters per revolution. Stone Speed v = CN/60 meters per second. Lap Time = 60/N seconds, and Grinding Distance = 60CN meters per hour.

Grinding Distance is accumulated path length at the entered constant speed, not the amount of ore ground. The selected radius identifies one representative circular path rather than every point on a finite drag stone.

At fixed rpm, doubling radius doubles circumference, speed and hourly distance, while lap time stays unchanged. At fixed radius, doubling rpm doubles speed and hourly distance and halves lap time.

The model contains no stone mass, contact force, friction, motor torque, ore properties, feed size or particle-size result. It therefore cannot find an optimum milling speed, drive power, animal workload or production rate.

Worked example: track speed at three rotation rates

Use radius r = 1.5 m. Track Length is 2π × 1.5 = 9.424778 m/rev, displayed as 9.4.

At N = 4 rpm, Stone Speed is 0.628319 m/s, displayed as 0.63. Lap Time is 15.0 seconds and Grinding Distance is 2261.9467 m/hr, displayed as 2262.

At 2 rpm, speed becomes 0.314159 m/s, lap time 30.0 seconds and hourly distance 1130.9734 m. At 8 rpm, speed becomes 1.256637 m/s, lap time 7.5 seconds and hourly distance 4523.8934 m.

These comparisons describe motion only. Doubling travel speed does not imply doubled throughput, and a particular speed does not establish whether a stone will skip, crush a given ore or remain in contact. The examples are not operating recommendations for an animal-driven or powered mill.

Different grinding motions

Mechanism Main motion
Drag-stone arrastra Stones are pulled around a fixed circular bed.
Roller or Chilean mill Heavy rollers travel around a pan or bed.
Stamp mill Raised stamps fall repeatedly onto the charge.
Rotating drum mill The drum moves grinding media and material inside it.

Comparing production capacity requires material tests and a defined machine. Generic tonnage, power and recovery figures cannot be derived from the circular speed equation.

Arrastra motion questions

No. It is the distance along the selected circular path in one hour at constant rpm. It has units of meters per hour, not mass per hour.

A stone following a circular path sweeps a band determined by its footprint and motion. The calculator specifies radius but does not model that coverage or material redistribution.

It doubles path speed in the calculation. Grinding output also depends on loading, ore properties, contact and other factors not represented here.

No. Mineral hardness alone would not describe a whole ore’s grindability, and the model has no material input.

No. Torque or resisting force is also needed. The calculator does not estimate either.

No. A working reproduction needs its own structural, drive and operating assessment. Historical dimensions are evidence of that site, not a rating for new construction.

No. It models circular travel only. Recovery and contamination are separate process and site-assessment questions.

Not necessarily. Different points on a sweep can lie at different radii. Each path has speed 2πrN/60, but this does not establish a suitable animal workload.

Historical reference

National Park Service: White’s Gulch arrastra nomination record. The description records the stone bed, drag blocks, central post remains and grinding marks at that site.

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: