Water Wheel Form 8: Flow, Head and Power Calculator

← Back to Engineering Library

This high-head wheel calculation converts entered steady flow and net head into gross hydraulic power, applies an entered overall efficiency, and divides the resulting illustrative shaft power by a chosen wheel speed.

Related Resources for Actuator Projects

For a separate actuator-driven gate or automation project, check the force application point and changing moment arm before choosing actuator stroke or force. The water-wheel calculator does not calculate gate actuator loads.

When comparing a cylinder to an electric actuator, convert the discussion into stroke, force, speed, duty cycle, and installed length. Matching one specification is not enough.

The actuator stroke should also be checked against the useful motion, not just against the visible travel. End clearance, hard stops, bracket rotation, and wire routing can all reduce the usable stroke in the final build.

  • Calculate actuator force at the worst bracket angle, not just at mid-stroke.
  • Check stroke, retracted length, and extended length against the mechanism envelope.
  • Confirm the structure can accept the higher loads created by a stronger actuator.

For a FIRGELLI actuator application, run the FIRGELLI actuator force calculator, then compare available stroke, force, and mounting envelope in the FIRGELLI linear actuator range. If the goal is to replace an existing unit, use the linear actuator replacement finder before assuming the new actuator is a direct fit.

Water Wheel Form 8 Interactive Calculator

Enter steady flow, net head, assumed overall efficiency and chosen wheel speed. Torque is a power/speed quotient and loss is a calculated difference—not a predicted operating curve or component loss breakdown.

0°

Gross hydraulic power
--
Illustrative shaft power
--
Chosen-speed torque
--
Arithmetic unconverted power
--

Equation Used

gross hydraulic power=rho g Q H; illustrative shaft power=eta P_h; arithmetic loss=(1-eta)P_h; chosen-speed torque=P_i/(2 pi n/60).
Flow, net head, efficiency and RPM are independent steady inputs. The loss output is only gross power minus efficiency-scaled power; it does not identify hydraulic, bearing, transmission or electrical losses.
  • Water density is 1000 kg/m3 and g=9.81 m/s2.
  • Entered flow and net head are steady and simultaneous.
  • Overall efficiency is entered and constant.
  • RPM is a chosen operating point, not solved from the hydraulic resource.
  • Intake, penstock, nozzle, buckets, tailwater, loss breakdown, governing, load and structure are omitted.
Same mechanism and inputs as the interactive calculator.

High-Head Flow–Head Calculation

The U.S. Department of Energy identifies flow and head as hydropower resource variables. The DOE Microhydropower Handbook provides the standard power equation and efficiency definition.

What This Calculator Represents

The tool evaluates one steady flow-head point, an entered overall efficiency, its arithmetic complement and torque at an independently chosen wheel rate.

Power, Loss Allocation and Torque

P_h=rho g Q H
P_i=eta P_h
P_loss=P_h-P_i
tau_i=P_i/omega

Loss is a calculated remainder, not a component model.

Worked Scenario

For 150 L/s and 6 m net head, gross hydraulic power is about 8.83 kW. At 65% entered efficiency, illustrative shaft power is about 5.74 kW and arithmetic loss 3.09 kW; at chosen 8 rpm, torque is about 6.85 kN m.

Assumptions and Limits

  • Calculated: steady flow-head power, entered-efficiency scaling, remainder and chosen-speed torque.
  • Illustrated: high-head admission, wheel and power calculation.
  • Not calculated: actual efficiency/speed, loss allocation, hydraulics, governing, load, structure or energy production.

Frequently Asked Questions

Is efficiency predicted?

No.

Is RPM predicted?

No.

Does loss identify where energy goes?

No; it is only P_h minus P_i.

Must head be net head?

Yes for the stated equation.

Are flow changes modeled?

No.

Can this size a real installation?

No.

References

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: