Sylvester–Kempe Linkage: Concept and Illustrative Budget

← Back to Engineering Library

The Sylvester–Kempe parallel motion belongs to the nineteenth-century family of exact straight-line linkages. Kempe's lecture describes its constrained link proportions and an accurately straight tracer path in the ideal rigid, pin-jointed geometry.

Sylvester-Kempe Linkage Interactive Calculator

Vary input half-angle, two entered mismatch magnitudes and entered radial clearance. Results show total sweep, mismatch norm, a stated simple budget and a normalized score against an explicit 1 mm display reference.

0°

Total sweep
--
Mismatch norm
--
Simple budget B
--
Score vs. 1 mm reference
--

Equation Used

sweep = 2 alpha; mismatch norm = sqrt(dL²+dS²); B = max(|dL|,|dS|)+2c; score = max(0,100(1−B/1 mm)).
B is an illustrative arithmetic budget, not off-axis motion. Actual path error requires the complete nominal linkage dimensions, pivot coordinates, assembly branch, individual joint clearances and a kinematic tolerance analysis.
  • Mismatch and clearance values are nonnegative user-entered magnitudes.
  • The coefficient 2 on clearance is an explicit display convention, not a derived worst-case stack.
  • The 1 mm score reference is arbitrary and carries no accuracy or acceptance meaning.
  • Elastic deflection, joint directionality, manufacturing covariance, load, dynamics and singular configurations are omitted.
Same mechanism and inputs as the interactive calculator.

The Historical Sylvester–Kempe Parallel Motion

Kempe's 1877 lecture describes a five-moving-piece Sylvester–Kempe parallel motion plus a moving seat and remaining link. With the specified pivot-distance equalities, the tracer P moves accurately in a horizontal straight line and the seat remains parallel to the fixed reference.

The Smithsonian's Sylvester–Kempe inversor model similarly documents linked triangular plates in which one point traces a circle while another traces a straight line. Straight-line motion depends on maintaining the complete specified link proportions and pivot constraints.

What This Explanatory Calculator Does

The calculator does not solve the historical linkage. It only summarizes four user-entered scenario values: angular sweep, Euclidean norm of two mismatch entries, a simple max-plus-clearance budget and a score against a 1 mm reference.

Use a dimensioned linkage definition and kinematic analysis to study actual tracer error or hardware tolerances.

Entered Budget Arithmetic

B = max(|ΔL|, |ΔS|) + 2c

The mismatch norm is sqrt(ΔL²+ΔS²). The score is 100(1−B/1 mm), clipped to zero through 100 percent. Neither B nor the score is derived from the Sylvester–Kempe constraint equations.

Worked Example: Arithmetic Only

For input half-angle 40 degrees, ΔL = 0.10 mm, ΔS = 0.10 mm and c = 0.05 mm, total sweep is 80 degrees, mismatch norm is 0.141 mm, B is 0.200 mm and the score against the 1 mm display reference is 80 percent.

This does not mean the tracer has 0.200 mm error or 80 percent straightness.

Model Boundary

  • Ideal mechanism: the correctly proportioned ideal parallel motion can produce an accurate straight-line tracer.
  • Calculated here: input sweep and the stated arithmetic over entered mismatch and clearance magnitudes.
  • Not calculated: link coordinates, exact path, stroke, transmission angle, singularity, assembly branch, tolerance sensitivity, clearance direction, elastic deflection, joint load, wear or dynamics.

Frequently Asked Questions

Is B the actual off-axis path error?

No. It is only the stated max-plus-clearance arithmetic.

Why is the ideal linkage exact?

Its full link proportions impose geometric constraints that place the tracer on a straight line in the ideal model.

What does the mismatch norm mean?

It is simply the Euclidean norm of the two entered mismatch magnitudes.

Why use a 1 mm score reference?

Only to normalize the display; it is arbitrary and not a tolerance.

Does input sweep determine stroke?

Not without the actual nominal link dimensions and geometry.

Can the calculator specify manufacturing tolerances?

No. That requires a dimensioned design and sensitivity or Monte Carlo analysis tied to actual requirements.

References

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: