Hart's A-frame: Straight-Line Linkage and Interactive Animation

← Back to Engineering Library

Hart's A-frame guides a tracing point along a straight line using five moving links and two fixed pivots. In the ideal geometry, the distances from the tracing point to the two fixed pivots remain equal. The point therefore stays on their perpendicular bisector. No sliding guide is needed to impose the line.

Hart's A-frame Interactive Calculator

Watch the connected A-frame move through a limited input arc. Build size sets its ground-pivot spacing. The other inputs compare a measured bar with its nominal dimension and state pin clearance; they do not predict the tracing point's straightness error.

Bar difference (mm)
--
Difference / span (%)
--
Difference / nominal (%)
--
Diametral clearance (mm)
--

Equation Used

e = |L_act − L_nom|; relative errors = 100e/S and 100e/L_nom; diametral clearance = 2c

The animated linkage has ideal rigid links and zero-clearance pivots. S is its ground span; long links are S, upper links and the cross-link are S/2, and the short end portions are S/4. The nominal and actual bar inputs are a separate dimensional comparison, not an imposed change to one of these links. Here c means radial pin clearance.

Hart's A-frame with two fixed pivots and a straight tracing path
Blue — Grounded arms. Gold — Cross-link. Violet — Links meeting at the tracing joint. Seven pivot circles connect five moving rigid links to a fixed base. The green tracing joint is found by intersecting circles about the two upper arm ends; it stays on the perpendicular bisector of the base. The ground span and long arms are S, the three shorter links are S/2, and the end portions beyond the cross-link joints are S/4. The green trace is not a mechanical guide. Crossed links occupy separate layers. Use the interactive animation above to follow the motion.

Two grounded arms and three connecting links

Fixed pivots A and B support equal arms AC and BD. Points E and F lie on those arms. Cross-link EF connects them, while links CP and DP meet at tracing joint P. The arrangement has five moving rigid links, plus the fixed frame: six links when ground is counted. There are seven revolute joints.

In the animated example, AC=BD=AB=S, CP=DP=EF=S/2 and CE=DF=S/4. These lengths satisfy b²=ac, with a=S, b=S/2 and c=S/4. Milton’s figure 2 illustrates this A-frame condition and its equal-distance property.

The input arm oscillates from 25° to 65° above the horizontal base. This chosen interval stays on one assembly branch, away from its folded and extended limiting positions. The green line is the path traced by P, not a rail or an additional member. Crossing bars have no joint unless a pivot circle is drawn.

Solve the joints, then examine the path

Place A at (−S/2,0) and B at (S/2,0). For input angle α, C=A+S(cos α,sin α), and E=A+3S/4(cos α,sin α). F is an intersection of the circle centred at E with radius S/2 and the circle centred at B with radius 3S/4. D lies on the same rigid arm: D=B+4(F−B)/3.

Finally, intersect circles of radius S/2 around C and D to obtain P. The illustration retains a continuous assembly branch. It does not assign a straight-line coordinate to P before solving the linkage.

For these proportions, AP=BP. Subtracting the two squared-distance equations gives x_P=0, the perpendicular bisector of AB. This is an ideal geometric result; finite pin play, dimensional errors and elastic bending can all change a real trace.

Compare dimensions without assuming a path error

At the default ground span S=100 mm, each long arm is 100 mm, the upper links and cross-link are 50 mm, and CE=DF=25 mm. At the middle input angle of 45°, the solved tracing joint is about 116.22 mm above the base. Over the chosen 25°–65° input interval, it moves approximately from 71.40 mm to 140.03 mm above the base.

A comparison bar measuring 50.05 mm against a nominal 50.00 mm has an absolute difference of 0.05 mm. That is 0.05% of a 100 mm span and 0.10% of its nominal length. Neither percentage is the tracing-point error.

If radial clearance c is 0.02 mm, the corresponding diametral clearance is 0.04 mm. Actual reversal play at P depends on which joints have clearance, the configuration, contact directions and loading. Adding the clearances does not establish a universal straightness band.

Demonstrating exact motion with revolute joints

The A-frame is useful for studying how fixed link lengths can impose an exact path without a prismatic joint. It also appears as a geometric building block in research on articulated structures; Milton uses its equal-distance property in his study of adaptable metamaterials.

A practical mechanism still needs space for layered links, suitable bearings, rigid supports and limits that keep it on the intended assembly branch. A straight ideal locus by itself establishes no load capacity, positioning accuracy or service life.

Ideal straightness and manufactured accuracy

Changing the relative lengths changes the closure geometry. To calculate the resulting path, specify which dimensions change and solve the altered linkage over its operating range. A single bar-error percentage cannot replace that calculation.

Similarly, the ground-span control scales this ideal example while the drawing automatically fits the available screen area. It changes the physical dimensions and tracing height, not the number of pixels occupied by the mechanism. Use Pause and the animation-position control to inspect the links at intermediate poses.

Frequently asked questions

Does Hart's A-frame have five or six links?

This example has five moving links and one fixed frame. It is a six-link mechanism when ground is included.

What keeps the point on a straight line?

The link proportions make AP and BP equal. With A and B fixed, P remains on their perpendicular bisector.

Is the green line a guide?

No. It is the computed path of the tracing joint. All the mechanical constraints come from fixed-length links and pivots.

Does the bar difference equal straightness error?

No. It compares two lengths. Predicting a tracing error requires the changed linkage geometry and, where relevant, a clearance and stiffness model.

Why do clearance inputs not distort the animation?

The animation demonstrates ideal geometry. The dimensional and clearance readouts are separate comparisons; there is no simulated tolerance distribution.

Can the input make a full revolution?

The illustrated assembly uses a restricted 25°–65° oscillation. It does not demonstrate full rotation or motion through singular configurations.

Mechanism references

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: