Hart's Exact Straight-Line Inversor: Stroke and Animation

← Back to Engineering Library

Hart's exact straight-line inversor uses a crossed cell and a circular input to make a marked point follow a straight path. The word exact describes its ideal geometry. Real accuracy depends on the manufactured links, joints and supports. This example calculates the crank swing needed for a requested stroke and shows the travel available within a defined nonsingular operating interval.

Hart's Exact Straight-Line Inversor Interactive Calculator

Enter the full long and short bar lengths and the desired straight-line stroke. The calculator reports the required input half-swing and limits the animation to the available demonstration range when the request is too large. Use long bars longer than the short bars.

Midpoint inversion K (mm²)
--
Required half-swing (deg)
--
Available displayed stroke (mm)
--
Animated full stroke (mm)
--

Equation Used

K = (L² − l²)/4; d = 2K/L; required half-swing = 2 atan(S_req/(2d)); S = 2d tan(θ/2)

The input crank has radius L/4 and the tracing points are at bar midpoints. Maximum displayed half-swing is min[65°, 0.8 × 2 acos(1−l/L)]. Actual animated stroke is the smaller of requested stroke and available displayed stroke. That display interval is not a load or safety rating. The model has rigid links and ideal pivots; it does not estimate machining-error or pin-clearance effects.

Midpoint Hart inversor sized for a 40 mm stroke
Blue and gold — Long bars. Violet — Short bars. Red — Input crank. Green — Tracing point. The crossed cell uses full long bars of 100 mm and short bars of 50 mm. A 25 mm crank drives the marked midpoint of the gold bar. The midpoint of the blue bar traces a line 37.5 mm from the fixed inversion centre. A 40 mm full stroke requires an input half-swing of about 56.145°. The green line is a trace rather than a guide; the long bars cross without a pivot. Use the interactive animation above to follow the motion.

A crossed cell with a grounded midpoint

Two long bars CD and EF have equal length L; short bars CE and DF both have length l. The long bars cross without a pivot at their crossing. A is the midpoint of CE and is fixed to the base. G is the midpoint of EF, and P is the midpoint of CD.

The red crank BG connects G to a second fixed pivot B. Its radius equals AB, so the circle traced by G passes through A. The complete straight-line mechanism has five moving links and the fixed frame, with seven revolute joints. P is a marked tracing point on CD, not a separate sliding joint.

Kempe’s 1877 lecture explains Hart’s crossed cell using corresponding division points on its bars. The midpoint version shown here is one particular choice of those points. The A-frame is another Hart straight-line arrangement; its connectivity differs from this crossed cell.

Define the lengths before calculating the constant

For the midpoint construction and full bar lengths used here, K=(L²−l²)/4. The points A, G and P are collinear and satisfy |AG|×|AP|=K on this branch. If half-bar lengths were used instead, the same constant would be written as their squared difference. The length definition matters.

Set A=(0,0), B=(R,0) and G=(R+R cos θ,R sin θ), with R=L/4. Circle closure determines E at distances l/2 from A and L/2 from G. Then C=−E and F=2G−E. D is the crossed-branch intersection of a circle of radius L about C and one of radius l about F. P=(C+D)/2.

Inversion gives P=K G/|G|². Substituting the input circle gives x_P=K/(2R) and y_P=[K/(2R)]tan(θ/2). Thus the path is a vertical line offset by d=K/(2R) from A. Its stroke between symmetric input limits ±θ_max is 2d tan(θ_max/2).

Example: a requested 40 mm stroke

For full long bars L=100 mm and full short bars l=50 mm, K=1,875 mm². The input crank radius is 25 mm, and the straight trace lies 37.5 mm from the fixed inversion centre.

A full stroke of 40 mm means tracing-point endpoints at y=−20 mm and y=+20 mm. The required input half-swing is 2 atan[40/(2×37.5)], about 56.145°. The total input angular excursion is about 112.29°.

This fits inside the selected 65° half-swing limit. The available displayed stroke at that limit is 47.78 mm. Requesting 80 mm with the same bars leaves available stroke at 47.78 mm and the animation uses that value, with a visible capped-stroke message.

Reach is a geometric condition

The cell can close only when (L−l)/2 ≤ |AG| ≤ (L+l)/2. For the chosen input circle this gives a limiting angle of 2 arccos(1−l/L). The illustration uses at most 80% of that limit and never more than a 65° half-swing. Those choices avoid the singular limit in the display.

The required-angle readout describes what the requested stroke would need from the inversion equation. If that angle exceeds the display limit, it is not a claim that the complete linkage can reach it. The separate available and animated stroke values show the range actually used.

When L≤l the chosen crossed-cell construction is invalid or degenerate. The calculator displays no motion results until the length relationship is restored. A physical mechanism also needs suitable stops, axial spacing, bearings and structural dimensions; these are not designed by this tool.

An exact ideal path without a rail

The marked midpoint of the blue long bar follows the green trace. The point is found from closed link loops, and the green line supplies no mechanical constraint. Fixed-length links and the red input crank provide the motion.

This makes a useful demonstration of how circular inversion turns a circle through its centre into a line. It also separates geometric reach from positioning accuracy: the equations alone do not specify micrometre straightness, allowable load, bearing fits or working life.

Use the bar dimensions to explore scaling and proportions. Then use the requested-stroke control to examine shorter or longer input excursions. The drawing fits the available screen area, so physical size changes are best read from the numerical dimensions and stroke values.

Frequently asked questions

What does exact mean here?

It means the ideal constrained tracing point lies on a mathematical line. It does not specify the accuracy of a manufactured assembly.

Why are requested and animated stroke different?

The request exceeds the demonstration’s available travel. The animation stops at the defined input-angle limit and reports its actual full stroke separately.

Is required half-swing the complete input angle?

No. The input moves from minus that angle to plus that angle about its central position. Total excursion is twice the half-swing, if it lies within the available range.

Why does the model use one input crank?

A midpoint of one short bar is fixed directly at A. A crank centred at B drives another midpoint around the required input circle. The four cell bars plus that crank are the five moving links.

Can the trace predict a manufacturing tolerance?

No. A tolerance analysis must identify which dimensions or joints differ, then solve their effects across the motion under the relevant loads.

Why must the long bar exceed the short bar?

That condition defines the positive midpoint inversion constant and the crossed-cell branch used here. Equal lengths are degenerate for this construction.

Mechanism references

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: