Kempe’s Universality Theorem: Working Linkage Example

← Back to Engineering Library

Kempe’s universality theorem says that the part of an algebraic plane curve inside a closed disk can be drawn by a suitable ideal linkage. It establishes what linkages can express, rather than promising a simple machine for every curve. Explore a concrete example below: a Peaucellier linkage whose tracing point follows a straight line when its input crank has the right radius.

Kempe’s Universality Theorem Interactive Calculator

The animation shows a Peaucellier inversor, one of the elementary linkage components discussed in treatments of Kempe’s theorem. Set the crank-to-offset ratio to 1 for a straight tracing path; other ratios give circular arcs. Change the link scale and input swing, then compare the calculated travel. This example does not synthesize a linkage for an arbitrary polynomial.

Mid-swing tracing x (mm)
--
Full vertical travel (mm)
--
Horizontal bow (mm)
--
Inversion constant K (mm²)
--

Equation Used

K = L² − s²; OA × OB = K; (c² − r²)(x² + y²) − 2Kcx + K² = 0. If r = c: x = K/(2c).

The two blue bars have length L. The four sides of the gold rhombus have length s=0.6L. The fixed centres are separated by c=0.3L; the pink input crank has radius r. For crank angle θ, B=(c+r cos θ, r sin θ) and A=KB/|B|². The green point A traces the curve. Mid-swing x means θ=0; vertical travel spans θ=−α to +α. Horizontal bow is the magnitude of x at an endpoint minus x at mid-swing. The animation rocks over this interval using the chosen cycle time. Ideal pivots and rigid bars are assumed, with one continuous, nondegenerate rhombus assembly selected. Extra bracing needed for a global construction proof, physical clearances, force and tracing errors are not modeled.

Peaucellier linkage: a working curve-tracing example 123
1 — Input crank. 2 — Rigid-bar cell. 3 — Tracing point and its straight path. Two blue bars and a gold rhombus invert the position of the crank endpoint. Equal crank radius and ground-pivot separation produce a straight tracing path without a sliding guide. This is an elementary linkage example, not a full construction for every algebraic curve. The drawing follows one rhombus assembly; additional proof bracing is not shown. Use the interactive animation above to follow the motion.

What the theorem says

An algebraic plane curve is described by a polynomial equation f(x,y)=0. A line and a circle are familiar examples. Kempe’s theorem concerns the portion of such a curve inside a closed disk and the existence of an ideal linkage that draws that set.

Kempe’s original 1876 argument allowed unwanted assembly configurations. Later rigorous treatments address those extra possibilities. Timothy Abbott’s 2008 thesis develops a corrected construction using braced linkage components, including angle operations, translation and straight-line constraints.

The animation shows a Peaucellier example, not the entire universality construction. Two blue bars meet at a fixed centre O. Four gold bars form a rhombus, and a pink crank pivots at the other fixed centre X. The crank moves point B around a circle, while the linked green point A follows its inverse path. No sliding guide constrains A.

From a circular input to an algebraic output curve

The equal blue bars have length L and the rhombus sides have length s. Geometry gives OA×OB=L²−s²=K, with O, A and B collinear on the selected assembly. With O at the origin, this means A=KB/|B|².

The crank circle is centred at X=(c,0), with radius r. Substituting the inversion relation into its circle equation produces (c²−r²)(x²+y²)−2Kcx+K²=0 for tracing point A. If r=c, the quadratic term vanishes and the result is the straight line x=K/(2c). If r differs from c, the traced curve lies on a circle. The finite links and chosen crank swing trace only an arc or segment.

At equal crank and offset, the full vertical travel over a half-swing α is 2[K/(2c)]tan(α/2). The horizontal bow is zero in the ideal model. For unequal r and c, the calculator evaluates A at the ends and middle of the same swing to find its vertical travel and horizontal bow.

Example: a straight line without a slider

For L=100 mm, the rhombus sides are s=60 mm and the fixed offset is c=30 mm. Choosing r/c=1 gives a 30 mm crank. The inversion constant is 100²−60²=6,400 mm², so the tracing line lies at x=6,400/(2×30)=106.67 mm from O.

With a 50-degree half-swing, the full vertical travel is 2×106.67×tan(25°), about 99.48 mm. The horizontal bow is zero. Change r/c away from 1 to see the path curve; changing L scales all lengths, while changing cycle time only changes playback.

Why the result matters

The theorem connects mechanical constraints with algebraic geometry. It shows that complicated paths need not be assigned to a moving point independently: in an ideal construction, the bar-length constraints themselves can impose the curve.

This is useful when studying linkage synthesis and the limits of mechanism design. It does not establish a compact layout, useful force transmission or practical manufacturing accuracy for a particular curve. Those require a specified mechanism and separate engineering analysis.

A working example is not a general construction

The pictured linkage has seven moving bars and a fixed separation between its two ground pivots. The animation follows one continuous rhombus assembly over a restricted input swing, staying away from collapsed configurations. It does not include the additional braces used to exclude all unwanted assemblies in a mathematical universality proof.

No polynomial-entry or general linkage-construction algorithm is provided here. The calculator describes only the dimensions and motion of this displayed example. It gives no universal bar-count estimate, tolerance, speed rating or force capacity.

Frequently asked questions

Does Kempe’s theorem mean one small mechanism can draw every curve?

No. It is an existence result for an appropriate ideal linkage and a specified algebraic curve within a bounded region. Different curves may require different constructions.

Is the animation a complete proof of the theorem?

No. It demonstrates a Peaucellier linkage that traces a line segment or circular arc. A general proof combines additional linkage components and must address alternative assembly configurations.

Why does r/c=1 produce a line?

The input circle then passes through the fixed inversion centre O. Under the relation A=KB/|B|², that circle maps to the line x=K/(2c), over the reachable portion shown.

Is the green trace a physical guide?

No. It marks the calculated path of point A. The rigid links impose the motion; there is no slider or guide on that point.

What changes when the crank radius is unequal to the offset?

The input circle no longer passes through O. Its inverse is a circle, and the chosen input swing traces a curved arc with nonzero horizontal bow.

Can these results predict real tracing accuracy?

No. The model assumes rigid bars and ideal pivots. Joint play, elastic deflection, dimensional errors and out-of-plane clearances are not calculated.

Mechanism references

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: