A trace spring adds compliance to the pulling connection between a harness and a vehicle or load. The tension-spring illustration shows extension as pull increases and recovery as it decreases. The calculator compares a normalized force range with two entered travel values; it does not predict the resulting motion of an animal and vehicle.
Trace Spring Interactive Calculator
Compare the entered pull range and spring travel. The midpoint and equivalent rate estimates are not a dynamic prediction of smoothing.
Equation Used
The default force reference is 100%, with an entered peak at 150% of that reference and trough at 50%. The tool divides half their difference by each travel value to give a normalized equivalent rate. It does not solve a force waveform or recommend a spring.
- Forces use an unspecified reference load; the Mean Pull control is a percentage of that reference, not newtons.
- The trace spring is treated as a linear Hooke-law spring.
- Each rate estimate divides the force half-range by one selected travel value; it does not use the difference between the two travel values.
- Damping losses, friction, and bottoming impacts are not included.
The midpoint of peak and trough is an arithmetic reference. Spring rate and available travel alone do not establish the actual smoothed horse/wagon force waveform; damping and inertia are not modeled.
Compliance in the trace
A trace transmits draught force from the harness to the load. A spring in that path changes length under load and stores elastic energy. As the load decreases, it can return that energy.
A spring alone is not a damper: storage and release do not establish how much an oscillating force will be reduced. The response also depends on inertia, damping, preload, routing and available travel. A simplified static relation is ΔF = kΔx over a linear working range.
Parts shown
- Harness-side connection: the input side of the trace.
- Tension spring: the extending elastic element.
- End attachments: transmit tension into and out of the spring.
- Vehicle-side connection: transfers pull to the drawbar or other attachment.
In a tension coil spring the coils separate during extension. Maximum extension and attachment strength are different questions from compression-spring coil bind. The schematic does not establish either limit.
A swingletree can balance the two traces of one animal; an evener can distribute pull among animals through their individual trees. Those functions are distinct from adding spring compliance.
Harness and vehicle context
Spring compliance is one feature that may be studied in a draught connection. The complete arrangement must also transmit, steer and restrain the load as required; a trace spring is not a vehicle brake or a substitute for appropriate harness fit.
Historical spring arrangements should be identified from the actual carriage or its documentation. This page does not attribute a particular spring design to a modern competition team, brewery or royal vehicle without evidence.
For an animal in work, spring calculations cannot establish comfort or explain sores. Harness condition and fit, workload and the animal’s condition require assessment in their own right. A numerical midpoint is not evidence that shoulder pressure has been made constant.
Normalized force and equivalent rate
Let M be Mean Pull in percent of a reference force. The peak A = M × Ppeak/100 and trough B = M × Ptrough/100 use that same reference. Peak Input displays A. Peak/trough midpoint displays (A + B)/2, and the half-range is H = max[0, (A − B)/2].
The calculator sorts the two travel entries. Soft Rate = H/larger travel and Stiff Rate = H/smaller travel, in reference-force percentage points per millimeter. They are not N/mm unless a reference force is supplied separately. The midpoint need not equal M and is not a measured time average.
The two travel numbers are separate divisors for this comparison. Their difference is not used in the rate formula. A physical spring measured between two force-displacement points would instead have secant rate k = (F2 − F1)/(x2 − x1).
If reference force Fref were known in newtons, a normalized rate r would convert as k = rFref/100 N/mm. Initial tension, preload, nonlinear behavior, dynamic response and allowable load are outside the calculator.
Worked example: reading the normalized values
Use Mean Pull 100%, Stride Peak 150% of mean, Stride Trough 50% of mean, Min Travel 25 mm and Max Travel 40 mm. Peak Input is 150.0% and the trough is 50%. Their midpoint is 100.0%, with half-range 50 percentage points.
Soft Rate is 50/40 = 1.25%/mm, and Stiff Rate is 50/25 = 2.00%/mm. These values describe the calculator’s half-range comparison. They do not prove that the vehicle sees a constant 100% pull.
For an explicitly assumed reference force of 400 N, the peak and trough would be 600 N and 200 N. The two normalized rates would correspond to 5 N/mm and 8 N/mm. Those conversions are arithmetic examples, not harness or spring recommendations.
Changing the trough to 40% leaves the peak at 150% but changes midpoint to 95%, half-range to 55, Soft Rate to 1.375%/mm (displayed 1.38) and Stiff Rate to 2.20%/mm. Reversing the order of the two travel entries does not change these rate results.
Spring, damper and rigid connection
| Element | Mechanical behavior |
|---|---|
| Steel spring | Stores and returns elastic energy within its working range; geometry and attachments determine capacity. |
| Damping element | Dissipates energy according to its motion-dependent characteristics. |
| Elastomeric element | May combine stiffness and damping that depend on material, temperature and rate. |
| Stiffer trace connection | Allows less extension, but still has material and attachment limits. |
No type is indefinitely strong or immune to fatigue. Service life, shock response and suitability cannot be assigned from this static normalized comparison.
Trace-spring questions
No. It is only the arithmetic midpoint of the two entered force limits. The calculator does not solve the vehicle-and-animal dynamics.
No. They are reference-force percentage points per millimeter. A separately known reference force is required to convert them to N/mm.
No. The model divides the force half-range separately by each travel entry. It is not a two-point force-extension measurement.
An ideal spring stores energy and returns it. Damping dissipates energy. Actual behavior depends on the complete system.
No. It contains no contact-pressure or animal-health model. Seek an appropriate harness-fit and animal-health assessment rather than changing trace length from these numbers.
Compression coil bind is not the same as maximum extension of a tension spring. Allowable extension, spring stress and end attachments need their own specifications.
No. Draught force also depends on the load, surface, gradient, vehicle and movement. The model neither measures that force nor establishes a safe workload.
The calculator cannot establish residual strength. Do not infer a safe capacity or repair method from this illustration; assess the actual component and its intended service.
Harness context
FAO: Matching tillage implements to draught animal potential discusses harness and load matching; pack animals and animal-drawn carts describes the connection through swingletrees and an evener. These references concern the complete draught arrangement, not a rating for the illustrative spring.
Building or designing a mechanism like this?
Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.