Light Electric Carriage: Grade-Force and Climbing-Power Calculator

← Back to Engineering Library

This electric-carriage screen compares the battery-side V×I input ceiling with the ideal mechanical power required only to climb the entered grade at constant speed.

Light Electric Carriage Interactive Calculator

Vary pack voltage, peak current, mass, road grade and climb speed. The comparison intentionally excludes rolling resistance, aerodynamic drag, acceleration and all electrical/mechanical losses, so it is not a drivetrain sizing result.

0°

DC input ceiling
--
Grade-only demand
--
Grade force
--
Ideal input fraction
--

Equation Used

theta=atan(G/100); F_grade=mg sin(theta); P_grade=F_grade v; P_DC=VI
V×I is a DC electrical input ceiling, while F_grade v is ideal mechanical grade power. Their ratio is shown only as a best-case fraction; real wheel power is lower than V×I and real road demand is higher than grade power alone.
  • The calculation assumes constant uphill speed on a constant grade. The reverse animation is only a replay.
  • Grade percentage is rise divided by horizontal run, so theta=atan(G/100).
  • Rolling resistance, aerodynamic drag, acceleration, accessories and conversion losses are excluded.

The power comparison isolates gravity on the selected uphill road. The return animation is a replay, and the page makes no battery-range or drivetrain-sizing prediction.

Battery input and road load

A battery supplies electrical power through a controller to a traction motor. A transmission transfers mechanical power to the wheels. This side-view schematic shows the carriage rolling on an inclined road; it does not expose the internal drivetrain.

The road angle follows the entered rise/run grade. Wheel rotation follows distance along that road without slipping. The second half of the animation replays the path backward so the climb can repeat; it is not a downhill braking or regeneration calculation. The results always describe the selected constant-speed uphill case.

The same carriage and grade calculation, following the inputs and playback controls above.

What this comparison is useful for

Use this calculator to explore how vehicle mass, road grade and constant uphill speed change the gravitational part of wheel power. The voltage and current inputs provide a separate battery-side electrical power ceiling.

The drawing represents a generic light electric carriage, not a particular make or model. It does not predict payload capacity, route range, operating cost, motor temperature, battery performance or suitability for a public road.

Grade force and power

theta=atan(G/100); Fgrade=mg sin(theta); Pgrade=Fgradev

The electrical ceiling is PDC=VI. The displayed percentage Pgrade/PDC is an ideal lower-bound share, not remaining usable power or a pass/fail margin.

Worked grade-only example

For a 600 kg carriage on an 8% grade, the road angle is atan(0.08), approximately 4.57 degrees. The downhill gravity component is 600 × 9.81 × sin(4.57 degrees), approximately 469 N.

At an uphill road speed of 20 km/h (5.56 m/s), the ideal power used to gain elevation is approximately 2.61 kW. A 72 V pack at an entered 200 A ceiling corresponds to 14.4 kW of electrical input. The grade-only result is approximately 18.1% of that input ceiling.

This comparison does not establish power reserve or battery range. It omits rolling resistance, aerodynamic drag, accessories, acceleration and conversion losses, and the entered current ceiling need not be a continuous rating.

Limits of the comparison

Increasing mass or grade increases the gravitational force along the road. Increasing speed increases the power needed to oppose that force. Changing pack voltage or the current ceiling changes the electrical comparison, not the force of gravity.

A result below 100% does not prove that a drivetrain can maintain the selected speed. A complete assessment needs the motor, controller, battery and transmission characteristics together with the remaining road loads. No equipment rating or product recommendation is inferred here.

Calculator questions

Does a zero-grade result mean the vehicle uses no power?

No. It means the gravitational grade component is zero. Rolling resistance, drag, accessories and conversion losses are outside this calculation.

Why is battery input different from wheel power?

Voltage times current describes electrical input. The controller, motor and transmission have losses, so those watts cannot all be assumed available at the tyres.

Does the return animation calculate regeneration?

No. It replays the climb backward for illustration. The output tiles remain the constant-speed uphill calculation.

Can the result determine battery size or diagnose a fault?

No. Route energy, usable capacity, temperature, duty cycle and component diagnostics require information this model does not contain.

Road-load reference

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: