A windmill converts energy in moving air into shaft rotation. This page illustrates a tower mill, with sails driving a windshaft and a right-angle gear pair transferring motion to a vertical shaft. The calculator compares speed and ideal torque ratios for that single gear stage. It does not calculate wind power, grain throughput or a complete mill’s gearing.
Ancient Windmill Gear Train Interactive Calculator
Vary sail speed and gear pitch diameters to compare the speed and ideal torque ratio of one right-angle gear stage.
Equation Used
For the single stage shown, output speed equals sail speed times brake-wheel pitch diameter divided by wallower pitch diameter. The Millstone Speed tile assumes the illustrated stone is directly coupled to that output. Any additional gearing in a real mill needs its own ratio. Defaults are illustrative: 2.4 m, 0.3 m and 15 rpm.
- Gear tooth count is proportional to pitch diameter.
- Ideal gear mesh with no slip or efficiency loss.
- Brake wheel drives the smaller wallower gear directly.
From sails to a vertical shaft
The sails and brake wheel share the windshaft. The brake wheel meshes with the wallower, turning the drive through a right angle. A smaller driven gear rotates faster than its driver. The animation shows the shafts and the meshing elements in a cutaway, with motion slowed for clarity.
The stone in this illustration is directly connected to the output shaft. Many actual mills have further gearing, such as a great spur wheel driving stone nuts. Those additional stages change the total speed ratio and are not included here. The number of teeth drawn is illustrative; the calculator uses entered pitch diameters.
Parts and functions
- Sails and windshaft: receive wind energy and turn the input shaft.
- Brake wheel: transmits motion and provides a surface for the mill’s brake.
- Wallower: receives motion on the vertical shaft.
- Output machinery: uses the transmitted rotation.
- Cap and yaw system: orient a tower mill’s sails toward the wind.
A post mill turns its body, while a tower or smock mill generally turns its cap. Other windmill traditions have vertical-axis rotors and different wind guidance. The tower-mill drawing does not represent every historical windmill.
Wind-driven machinery
Windmills have powered grain grinding, water lifting and other machinery. The work performed depends on the equipment connected to the drive, rather than on the gearing alone. A grain mill, drainage mill and sawmill therefore need different machinery downstream of their wind input.
Green’s Mill in Nottingham provides an example of the several shafts and gear stages inside a working grain mill. Its guide is useful for comparing this simplified one-stage animation with a real installation. Real tooth counts, dimensions and operating procedures must come from the particular mill.
One ideal gear stage
Let R = Dbrake/Dwallower, using compatible pitch diameters. Output speed is Nout = NsailR. Speed Gain is Nout − Nsail in rpm. Torque at Stone is 100/R percent of input torque for the illustrated direct output and an ideal lossless mesh.
Pitch diameter is the diameter used for gear ratio, not necessarily the outside diameter measured over tooth tips. For compatible gears the same speed ratio can be obtained from driving tooth count divided by driven tooth count.
Speed increase trades away torque; it does not create power. At steady ideal operation, Tin × ωin = Tout × ωout. Actual losses reduce delivered power and torque. Since input torque is not entered, the percentage tile cannot provide torque in N·m.
Wind speed, sail area and aerodynamic behavior are not inputs. The selected sail rpm is an assumed operating speed, not a prediction from weather. Additional stages would multiply the speed ratios and add losses.
Worked example: speed increase and torque ratio
Use Sail Speed 15 rpm, Brake Wheel Dia 2.4 m and Wallower Dia 0.3 m. The ratio is 2.4/0.3 = 8:1. Millstone Speed is 120 rpm, Speed Gain is 105 rpm and ideal Torque at Stone is 12.5% of input torque.
Change only Wallower Dia to 0.6 m. The ratio becomes 4:1, output speed is 60 rpm, speed gain is 45 rpm and ideal output torque is 25% of input. This compares gearing; it does not say either arrangement has adequate tooth strength or suitable millstone speed.
With the original 8:1 ratio, increasing Sail Speed to 20 rpm gives output speed 160 rpm and gain 140 rpm. Torque percentage remains 12.5%. The calculator does not determine the power or torque available from the sails at either speed.
Mechanism choices
| Arrangement | How it differs |
|---|---|
| Post mill | The mill body turns to face the wind. |
| Tower or smock mill | The cap turns while the main building remains fixed. |
| Vertical-axis mill | The rotor turns about a vertical axis and uses different wind guidance. |
Site, construction, sails, machinery and maintenance determine performance. Neither a universal wind-speed operating range nor a safe gearing arrangement follows from the mill type. Braking, sail handling and repairs require the procedures and expertise appropriate to that installation.
Windmill gearing questions
No. It is the output speed of the single ideal stage shown, assuming a directly coupled stone. Further gearing changes a real mill’s total ratio.
It is ideal output torque as a percentage of input torque: 100 divided by the speed ratio. It is not torque in N·m, tooth capacity or a measured efficiency.
Use compatible pitch diameters or establish the ratio from tooth counts. Outside diameter over tooth tips is not generally the pitch diameter.
No. Sail rpm is entered directly. Wind speed, sail dimensions, aerodynamic coefficients and load behavior are not modeled.
That percentage depends only on gear ratio. It does not establish that actual input torque remains constant as the mill speeds up.
No. An ideal speed increase reduces torque in inverse proportion, preserving power. Real gears also lose power through friction and other losses.
No. They do not model brake capacity, sail loads, overspeed or structural strength. Use the mill’s specific procedures and a qualified millwright for those tasks.
The playback is slowed to show the gear motion clearly. Numerical speed outputs still use the entered rpm and pitch-diameter ratio.
References and further reading
A Short Guide to Green’s Mill describes an actual mill’s windshaft, gearing and grinding machinery. National Trust: Bembridge Windmill identifies the sails, windshaft and brake wheel in the surviving mill.
Building or designing a mechanism like this?
Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.