Valve Gear: Ideal Gross Lift from Lobe Lift and Rocker Ratio

← Back to Engineering Library

An engine valve train can use a cam, follower, pushrod and rocker to transmit cam lift to a poppet valve. This calculator multiplies an entered lobe lift by an entered nominal rocker ratio as an ideal gross-lift reference.

Considering an actuator-operated valve

An actuator-operated valve requires its own force, stroke and timing analysis. The lobe-lift and rocker-ratio calculation below does not size an actuator or establish whether it can follow an engine valve cycle.

For cam-driven motion, look for dwell, rapid lift, and shock loading. A linear actuator may simplify positioning, but it will not naturally reproduce a cam profile unless the control system is designed for it.

If extra force is added as a margin, confirm that the frame, hinge, pins, and brackets can take the load. A stronger actuator can protect the motor from stalling while quietly moving the failure point into the structure.

  • Calculate actuator force at the worst bracket angle, not just at mid-stroke.
  • Check stroke, retracted length, and extended length against the mechanism envelope.
  • Confirm the structure can accept the higher loads created by a stronger actuator.

For a FIRGELLI actuator application, run the FIRGELLI actuator force calculator, then compare available stroke, force, and mounting envelope in the FIRGELLI linear actuator range. If the goal is to replace an existing unit, use the linear actuator replacement finder before assuming the new actuator is a direct fit.

Valve Gear Interactive Calculator

Enter lobe lift and a nominal rocker ratio. Results are ideal gross-lift arithmetic—not measured net lift, a cam profile, valve timing, spring or clearance analysis, or an engine recommendation.

0°

Ideal gross valve lift
--
Ideal gross valve lift
--
Nominal ratio increase
--
Added ideal lift
--

Equation Used

ideal gross valve lift=L_lobe R; metric lift=25.4 L_valve; ratio increase=(R-1)100%; added ideal lift=L_valve-L_lobe.
U.S. Patent 11,287,250 states valve lift=cam lift multiplied by rocker ratio. Actual motion can differ with changing contact geometry, lash, deflection and component tolerances.
  • Entered lobe lift is treated as a scalar maximum lift.
  • Entered rocker ratio is treated as constant through the motion.
  • The result is ideal gross lift before lash, preload, deflection and contact-geometry effects.
  • The animation is a generic OHV topology and phase cue, not a solved cam profile or exact linkage closure.
  • Duration, timing, acceleration, jerk, forces, spring loads, valve float, interference, clearances, wear, lubrication, RPM, power, emissions and safety are omitted.
Same mechanism and inputs as the interactive calculator.

Documented Valve-Train Topology

U.S. Patent 2,939,443 describes an overhead-valve mechanism in which rocker leverage can produce valve lift greater than cam lift. U.S. Patent 8,794,204 documents a camshaft lobe, rocker arms, a valve-lift mechanism and a poppet valve. These sources support the generic topology, not a universal cam profile.

What This Calculator Represents

The tool multiplies entered lobe lift by an entered nominal rocker ratio, converts the result to millimetres and reports the arithmetic increase over a 1:1 lever.

Ideal Gross-lift Calculation

ideal gross valve lift = lobe lift × nominal rocker ratio
metric lift = 25.4 × inch lift
ratio increase = (R - 1) × 100%
added ideal lift = gross valve lift - lobe lift

Patent literature also notes that actual rocker contact position and tolerances influence achieved lift, which this constant-ratio calculation omits.

Worked Arithmetic Example

At 0.350 in entered lobe lift and 1.60:1 nominal rocker ratio, ideal gross valve lift is 0.560 in, or 14.22 mm. The ratio is 60% above 1:1 and adds 0.210 in in this ideal arithmetic.

Model Boundary

  • Calculated: ideal maximum lift multiplication and unit conversion.
  • Illustrated: generic cam, follower/pushrod, rocker and valve topology.
  • Not calculated: actual motion profile, lash, preload, deflection, contact sweep, timing, duration, spring force, valve float, interference, clearance, stress, RPM, power, life or safety.

Frequently Asked Questions

Is the output measured net valve lift?

No; it is ideal gross lift.

Does the calculator subtract lash?

No.

Is rocker ratio constant in every real mechanism?

No; contact geometry can change effective ratio through motion.

Does the animation reproduce a cam profile?

No.

Can the result prove spring or piston clearance?

No.

Can it select a camshaft or rocker?

No.

References

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: