Cornish Engine Valve Gear: Plug Rod, Tappets and Travel Ratios

← Back to Engineering Library

Historic Cornish pumping engines used beam-driven plug rods, tappets and levers to operate valves. This calculator compares entered tappet drop, piston stroke, plug-rod travel and stroke rate as a dimensional comparison; actual trip timing and the complete valve sequence are not calculated.

Valve Gear of a Cornish Engine Interactive Calculator

Enter tappet drop, piston stroke, plug-rod travel and strokes per minute. Results are ratio arithmetic—not steam cutoff, valve-open duration, trip timing, engine setting or performance.

0°

Tappet / plug travel
--
Proportional piston scale
--
Entered stroke interval
--
Piston / plug mismatch
--

Equation Used

travel ratio=100 h/Sr; proportional piston scale=h Sp/Sr; entered stroke interval=60/N; piston/plug mismatch=100 abs(Sp-Sr)/Sr.
The proportional piston-travel value assumes only a linear scale between the two entered stroke magnitudes. It does not establish a physical plug-rod/piston relationship or a trip event.
  • All four quantities are entered independently.
  • Travel ratio is tappet drop divided by entered plug-rod travel.
  • Proportional piston scale applies the same entered fraction to entered piston stroke.
  • Stroke interval is the reciprocal of entered strokes per minute.
  • The animation illustrates a rocking beam, plug rod, tappet, lever and moving poppet. Its drawing dimensions and illustrative lift do not establish the geometry or valve sequence of a particular engine.
  • Valve positions, trip geometry, cataracts, catches, phase, delays, flow, pressure, forces, duty, efficiency, wear, settings and safety are omitted.
Same mechanism and inputs as the interactive calculator.

Documented Cornish-Engine Topology

William Pole's 1844 treatise documents the Cornish pumping engine, its indoor and outdoor strokes, valves and engine regulation. An 1859 Philadelphia Water Department report describes tappets on a plug rod suspended from the beam contacting handles that operate the steam and exhaust valves. Gardner D. Hiscox also illustrates a Cornish-engine trip-poppet-valve gear.

What This Calculator Represents

The tool reports an entered tappet-drop/plug-travel ratio, applies that same ratio to entered piston stroke as a proportional scale, converts entered strokes per minute to seconds per stroke and compares the two entered stroke magnitudes.

Entered Travel-ratio Comparison

tappet / plug ratio = h / Sr
proportional piston scale = h Sp / Sr
entered stroke interval = 60 / N
piston/plug mismatch = |Sp - Sr| / Sr

None of these ratios identifies when a real valve trips. That requires the complete engine geometry and operating sequence.

Worked Ratio Example

With 36 in tappet drop, 120 in piston stroke, 120 in plug-rod travel and 8 strokes/min, the entered travel ratio is 30%, the proportional piston scale is 36 in, the entered stroke interval is 7.50 s and the two entered stroke magnitudes match.

Model Boundary

  • Calculated: entered travel ratio, proportional scale, reciprocal stroke interval and stroke-magnitude mismatch.
  • Illustrated: generic beam, plug rod, tappet, lever and valve topology.
  • Not calculated: actual trip point, valve-open time, valve sequence, steam cutoff, cataract delay, linkage closure, pressure, flow, loads, duty, efficiency, settings or safety.

Frequently Asked Questions

Is the travel ratio steam cutoff?

No.

Is the stroke interval valve-open time?

No; it is simply 60 divided by entered strokes per minute.

Does the proportional piston scale prove the real kinematics?

No.

Does the animation reproduce a specific Cornish engine?

No.

Does the travel ratio define a recommended setting?

No. The ratio compares the entered dimensions. A real setting depends on the complete trip mechanism and operating sequence.

Can this set or operate real trip gear?

No.

References

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: