Riefler Double Escape Wheel: Front View and Reference Comparisons

← Back to Engineering Library

Sigmund Riefler's 1893 patent describes a double escape wheel on one axis: a driving wheel with bevel tooth surfaces and a larger locking wheel with radial tooth surfaces. Each cylindrical, half-cut pallet engages both wheels, and the anchor bends the pendulum suspension spring to transmit impulse.

Two Escape-wheel Pallet Escapement Interactive Calculator

Enter a normalized total, an arithmetic divisor, an equal-array tooth count and an angular offset. The results are calculation comparisons only—not pallet contact load, Riefler wheel phasing, drop, lock, impulse energy or clock performance.

0°

Arithmetic equal share
--
Equal-share reduction
--
Half-tooth-pitch reference
--
Offset minus reference
--

Equation Used

arithmetic share=entered total/divisor; equal-share reduction=100(1-1/divisor); half-tooth-pitch reference=180 degrees/N; difference=entered offset-reference.
The equal-share calculation is a hypothetical division of a normalized number. Riefler's driving and locking wheels have different functions, so the result must not be interpreted as physical load sharing. The 180/N quantity is only half the pitch of an ideal equal-tooth array.
  • The entered total is a normalized comparison value, not a measured force, torque or energy.
  • The divisor is an arithmetic choice of one or two, not the number of simultaneous active Riefler contacts.
  • The tooth-count calculation describes an ideal equal angular array only.
  • No patent dimension establishes the entered offset as a Riefler setting.
  • Pallet geometry, tooth profiles, depthing, drop, lock, clearance, spring stiffness, pendulum dynamics, torque, friction, wear, tolerances, rate and safety are omitted.
Same mechanism and inputs as the interactive calculator.

Riefler's Coaxial Driving and Locking Wheels

Riefler patent 508,760 describes a double wheel on one axis. The driving wheel H uses bevel tooth surfaces; the larger locking wheel R uses radial surfaces. Each cylindrical pallet S is cut away at its front end and provides a cylindrical driving surface plus a plane locking surface.

As the pendulum and anchor move, a locking tooth leaves a pallet, the wheels advance, a driving tooth moves the anchor in the opposite direction and the anchor bends the pendulum suspension spring. The stored spring tension supplies the pendulum impulse.

What This Calculator Represents

The controls perform two independent arithmetic comparisons: division of an entered normalized total by one or two, and comparison of an entered angle with half the pitch of an ideal equal-tooth array.

Those calculations do not reconstruct Riefler's tooth profiles, pallet geometry, depthing, drop, lock or impulse transfer.

Limited Arithmetic Only

arithmetic share = entered normalized total / divisor
equal-share reduction = 100 × (1 - 1/divisor)
half-tooth-pitch reference = 180° / N
difference = entered offset - reference

The patent does not say that its functionally different driving and locking wheels equally share load. The half-pitch result is a geometric reference, not a validated Riefler adjustment.

Worked Arithmetic Example

With entered total 100 and divisor 2, the hypothetical equal share is 50 and the reduction relative to a divisor of one is 50%. For 30 equally spaced teeth, half a tooth pitch is 6°. An entered 6° offset therefore differs from that reference by 0°.

Assumptions and Limits

  • Illustrated arrangement: coaxial driving and locking wheels, two common pallets, anchor and suspension-spring impulse path.
  • Calculated: normalized division and ideal equal-array angular calculation.
  • Not calculated: actual contact force, load sharing, tooth or pallet geometry, depthing, drop, lock, impulse, spring energy, pendulum motion, rate, wear, tolerances or suitability.

Frequently Asked Questions

Do the two Riefler wheels perform the same job?

No. The patent distinguishes a driving wheel H and a larger locking wheel R.

Does each wheel take half the physical load?

This calculator does not establish that.

Is 180/N the required Riefler wheel offset?

No. It is only half the pitch of an ideal equal-tooth array.

Do the pallets engage both wheels?

Yes. The patent describes each pallet as having surfaces for both driving and locking engagement.

Is impulse energy calculated?

No.

Can this set up or rate a precision clock?

No.

References

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: