A gas-motor passenger car carries its engine on board and transmits mechanical power to a driven axle. The animation shows an idealized gear-and-chain drivetrain with an adjustable overall reduction. Use the calculator to compare engine torque, wheel torque, rim pull and wheel speed under its constant-power assumptions.
Street Railway Gas Motor Passenger Car Interactive Calculator
Explore an ideal steady-state drivetrain for the article's gas-motor passenger car. Horsepower is treated as available throughout the sorted RPM band; the lower endpoint sets the torque case and the upper endpoint sets the speed case.
Equation Used
- The two entered engine speeds are sorted before use; Nlo supplies the constant-power torque case and Nhi supplies the ideal-speed case.
- Horsepower is constant across the entered band and the entered ratio represents the complete engine-to-front-driven-axle reduction.
- The drawing divides the entered ratio into equal illustrative gear and open-chain stages, √G × √G = G. The tangent pitch circles and sprockets are mechanically coherent, but this equal split is not asserted as the historical McKeen tooth-count arrangement.
- Gear and chain losses, clutch slip, wheel slip, grade, rolling resistance, aerodynamic drag, engine torque-curve variation and component strength are omitted.
The front axle is driven through an external-gear stage and an open-chain stage. Each illustrates a reduction of √G, giving the entered overall reduction G.
Following power to the axle
The displayed engine shaft drives an intermediate shaft through an external gear pair. An open chain then connects the intermediate shaft to the front driven axle. The gear mesh reverses direction; the open chain preserves the intermediate shaft’s direction.
Each illustrated stage has reduction √G, so their product is G. The intermediate shaft turns at −1/√G times engine speed, and the driven axle at −1/G times engine speed. This equal split makes the adjustable overall ratio visible; it is not a reconstruction of historical tooth counts.
Main elements
- Engine: supplies the assumed horsepower.
- Gear stage: changes shaft speed, torque and direction.
- Intermediate shaft: connects the two stages.
- Chain stage: delivers motion to the driven axle.
- Driving wheels: convert ideal axle torque to tangential force at the rim.
The cited historical account describes a gasoline engine, sliding-gear transmission and silent-chain drive to a front axle. The animation simplifies that power path and does not model clutch operation or gear selection.
What the drivetrain model explains
An onboard engine allows a rail passenger car to carry its source of mechanical power. In a mechanical drive, gears and a final drive connect that engine to the wheels; in an electric transmission, a generator and traction motors perform different roles.
The calculator demonstrates the mechanical ratio and wheel-size relationships. It does not estimate route performance, fuel consumption, passenger capacity, adhesion or a historical vehicle’s operating limits.
Torque, rim pull and ideal wheel speed
Using horsepower P and the lower entered rpm Nlo, engine torque is Te = 5252P/Nlo in lb-ft. Ideal wheel torque is Tw = TeG. With wheel diameter D in inches, radius in feet is D/24, so rim pull is F = Tw/(D/24) in lbf.
At the higher entered rpm Nhi, ideal speed is v = (Nhi/G)Ï€(D/12)60/5280 in mph. The two speeds are sorted before use. Horsepower is treated as constant across the band.
The torque and rim-pull outputs belong to the low-rpm case; the speed output belongs to the high-rpm case. They are not a simultaneous operating point. The model omits drivetrain losses, wheel slip, grade, rolling resistance and aerodynamic drag.
Worked example: two ideal endpoint cases
Use illustrative inputs of 100 hp, 500–1,000 rpm, overall reduction G = 4 and wheel diameter D = 36 in.
- At 500 rpm, engine torque = 5252 × 100/500 = 1,050.4 lb-ft.
- Ideal wheel torque = 1,050.4 × 4 = 4,201.6 lb-ft. Wheel radius is 1.5 ft, giving rim pull ≈ 2,801.1 lbf.
- At 1,000 rpm, wheel speed is 250 rpm and ideal vehicle speed is about 26.77 mph.
Doubling the reduction to 8 doubles ideal torque and rim pull and halves the high-rpm speed, with the other inputs unchanged. This does not establish that a vehicle can start a load or sustain that speed against real resistance.
Understanding the ratio trade-off
| Change | Effect in this ideal model |
|---|---|
| Increase reduction G | More wheel torque and rim pull; less wheel speed at the same engine rpm. |
| Increase wheel diameter | More distance per revolution; less rim pull at the same axle torque. |
| Increase assumed horsepower | More calculated torque at the same low rpm; no change to the purely geometric high-rpm speed. |
Real ratio selection also depends on the engine curve, transmission ratings, wheel adhesion and route loads. Those are outside this calculator.
Frequently asked questions
Are maximum rim pull and top speed available together?
No. Rim pull uses the lower rpm endpoint, while speed uses the higher endpoint. They describe separate ideal cases.
What happens if I enter the rpm limits in reverse order?
The calculator sorts them. The lower value sets the constant-power torque case and the higher value sets the speed case.
Why does horsepower not change the speed result?
The speed calculation uses engine rpm, reduction and wheel circumference. It does not check whether enough power is available to overcome resistance at that speed.
Is rim pull the same as available drawbar pull?
No. The calculated rim force includes no rolling resistance, grade, aerodynamic drag or adhesion limit. Available force for pulling or acceleration would need those additional effects.
Does the two-stage drawing reproduce a particular historical gearbox?
No. It divides the entered reduction equally between illustrative gear and chain stages. The historical reference supports the general drivetrain type, not that exact ratio split.
Can the calculator diagnose clutch slip or choose a chain?
No. Component strength, clutch behavior, lubrication, wear and drivetrain losses are not modeled.
References
Building or designing a mechanism like this?
Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.