Hydraulic Piston Force Calculator: Pressure and Bore | FIRGELLI

← Back to Engineering Library

This calculator converts entered hydraulic pressure and full cylinder bore into ideal gross cap-end piston force. It does not size, rate or approve a cylinder or hydraulic system.

Hydraulic Device Interactive Calculator

Explore the ideal static relation F=P A for pressure acting uniformly over a circular full-bore piston area.

0°

Full-Bore Area
--
Ideal Gross Force
--
Ideal Gross Force
--
Force in tonne-force
--

Equation Used

A=pi d^2/4; ideal gross cap-end force F=P A; 1 bar=100,000 Pa; 1 tonne-force=9,806.65 N
Ideal static full-bore cap-end force only. No efficiency factor or safety factor is implied.
  • Entered pressure acts uniformly on the full cap-end area. The calculation assumes zero opposing rod-side gauge pressure and omits friction.
  • Static incompressible-fluid comparison with no acceleration or pressure transient.
  • No rod-side annular area or backpressure, seal/bearing friction, leakage or pressure loss.
  • No cylinder wall, rod buckling, mounts, pins, frame, hose, fitting, valve, pump, relief, stability, fatigue, duty-cycle or applicable-code model.

The tonne-force output is only a force-unit conversion, not a lifting-capacity rating. Real available force is reduced by rod-side backpressure, seal friction and other losses, while allowable load also depends on structure, mounting, stability and dynamic effects.

Related video: telescopic hydraulic cylinder
Video: Hydraulic telescopic cylinder 2 by Nguyen Duc Thang (thang010146) on YouTube. A telescopic cylinder has multiple moving stages; the calculator below uses one fixed full-bore area and does not model those stages.
Same mechanism and inputs as the interactive calculator.

Ideal pressure-area relation

Uniform cap-end pressure P acting over full piston area A produces a gross force F = PA. For a circular bore of diameter d, A = πd²/4. This is the cap-end contribution before subtracting rod-side pressure force and friction.

The animation is a static pressure-and-force diagram. It does not represent cylinder travel, speed or a particular hydraulic machine.

Use as a unit and first-principles check

The calculator can verify pressure-area-force arithmetic for a hypothetical cap-end scenario. It cannot select a cylinder, pump, hose, valve, relief setting or safe load.

Gross cap-end force

Convert pressure from bar to pascals with P(Pa)=100,000P(bar), convert bore from millimetres to metres, compute A=pi d²/4, then F=P A. The kN and tonne-force tiles are conversions of the same ideal force.

Retraction force requires the annular piston area and rod-side differential pressures, neither of which is entered here.

Worked force example

At 250 bar and 100 mm bore, full-bore area is 78.54 cm². Ideal gross cap-end force is 196,350 N, or 196.35 kN and about 20.02 tonne-force.

Scope and limitations

Real engineering requires cylinder pressure ratings and proof data; bore, rod, wall and end-cap geometry; rod buckling and side load; mounts, pins and frame strength; pressure losses and backpressure; seals, friction and leakage; load stability, acceleration and shock; hoses, fittings, valves, pump, relief and controls; duty cycle, fatigue, guarding and applicable regulations.

Questions

Is tonne-force a safe lifting capacity?

No. It is only a unit conversion of ideal gross force.

Does this calculate retraction force?

No. Retraction requires rod diameter and rod-side pressure.

Can pressure and bore select a cylinder?

No. Strength, stability, mounting, dynamic load and component ratings are not checked.

Calculation basis

Pressure is force per unit area. Multiplying the entered cap-end pressure by πd²/4 therefore gives the ideal gross force on a circular piston. Pressure in bar is multiplied by 100,000 to obtain pascals, and bore in millimetres is divided by 1,000 to obtain metres.

Newtons, kilonewtons and tonne-force express the same result in different units. The tonne-force uses standard gravity, 9.80665 m/s². Cylinder selection also requires the opposing chamber pressure, rod diameter, friction, component ratings and mechanical load checks; the slider ranges are example inputs, not pressure recommendations.

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: