Cone-drive Ratio: One-point Pitch-diameter Comparison

← Back to Engineering Library

At one operating point, an ideal belt drive can be described by two effective pitch diameters. This calculator reports their ideal speed ratio and checks whether their sum matches an entered target.

Considering an actuator for sheave adjustment

An actuator used to adjust sheave spacing needs a defined travel range, axial force and control method. The diameter comparison below does not calculate those requirements or the relationship between actuator position and effective pitch diameter.

Where springs or counterbalances are involved, calculate the actuator force over the full travel. The highest load may occur at a different position than the most obvious one.

For machines that move around people, control review should include what happens after power loss, a jam, a stalled motor, or an unexpected command. Those conditions are part of good motion-control engineering.

  • Use loaded speed, not only no-load speed, when timing the motion.
  • Confirm voltage, controller rating, and limit-switch behavior before wiring.
  • Use feedback when synchronized or repeatable position control is required.

For FIRGELLI actuator control, use the linear actuator wiring diagram generator before wiring the final circuit and compare suitable actuator families in the FIRGELLI linear actuator range. If the machine already has an actuator, the linear actuator replacement finder can help shortlist replacements.

Variable Speed Cone Gearing Interactive Calculator

Enter two effective pitch diameters and a target sum. Results describe one ideal no-slip operating point—not complete cone profiles, belt travel, center distance, belt length or capacity.

0°

Ideal speed ratio
--
Ideal reciprocal torque factor
--
Entered diameter sum
--
Diameter-sum difference
--

Equation Used

q=D1/D2; ideal torque factor=D2/D1; diameter sum=D1+D2; sum error=D1+D2-S.
A constant diameter sum can be a design constraint for complementary variable sheaves, but matching it at one point does not establish belt length, constant center distance or valid cone geometry across a range.
  • D1 and D2 are positive effective pitch diameters at one operating point.
  • The belt has no slip at the pitch line.
  • The reciprocal torque factor assumes lossless equal-power transmission.
  • Target sum is an entered comparison value, not a derived belt-length condition.
  • Cone profiles, axial belt position, center distance, wrap, tension, slip, efficiency, stress, wear, guarding and safety are omitted.
Same mechanism and inputs as the interactive calculator.

One-point Effective-diameter Comparison

The U.S. Department of Energy defines belt-drive ratios using effective pitch diameters. NASA variable-speed belt-drive tests show that real variable sheaves also depend on axial force, traction, centerline force and efficiency. This calculator checks one entered diameter pair and target sum only.

What This Calculator Represents

The tool divides D1 by D2 for ideal speed ratio, reports the reciprocal equal-power factor, adds the entered diameters and subtracts an entered target sum.

Ideal Diameter-pair Calculations

q=D1/D2
ideal reciprocal torque factor=D2/D1
diameter sum=D1+D2
sum error=D1+D2-S

Zero sum error means only that the entered pair matches the entered sum constraint.

Worked Idealized Example

For D1=125 mm, D2=50 mm and target sum 175 mm, the ideal speed ratio is 2.50:1, reciprocal factor is 0.40, diameter sum is 175 mm and sum error is zero.

Model Boundary

  • Calculated: ideal one-point diameter ratio, reciprocal factor, diameter sum and difference from an entered target.
  • Illustrated: one open-belt operating point using exact relative pitch diameters.
  • Not calculated: complete cone or sheave profiles, axial belt travel, center distance, belt length, wrap, tension, slip, efficiency, actual torque, stress, wear, capacity or safety.

Frequently Asked Questions

Does zero sum error prove constant belt length?

No.

Does this generate cone profiles?

No.

Is torque factor actual output torque?

No; it is only the ideal reciprocal ratio.

Are center distance and belt length calculated?

No.

Are slip and efficiency included?

No.

Can it rate a physical drive?

No.

References

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: