Two selectable gear paths provide alternative speeds on one output shaft. Compare their ideal ratios and follow the selected path in the animation. The collar illustrates selection; its design is not specified in the short caption of Brown’s movement 200.
Practical actuator checks for Two-velocity Gears on Same Shaft
The practical actuator review for two-velocity gears on same shaft is mainly about controlled travel. Define the start point, end point, load direction, speed requirement, and whether open-loop timing is good enough or feedback is required.
When comparing a cylinder to an electric actuator, convert the discussion into stroke, force, speed, duty cycle, and installed length. Matching one specification is not enough.
For machines that move around people, control review should include what happens after power loss, a jam, a stalled motor, or an unexpected command. Those conditions are part of good motion-control engineering.
- Use loaded speed, not only no-load speed, when timing the motion.
- Confirm voltage, controller rating, and limit-switch behavior before wiring.
- Use feedback when synchronized or repeatable position control is required.
For FIRGELLI actuator control, use the linear actuator wiring diagram generator before wiring the final circuit and compare suitable actuator families in the FIRGELLI linear actuator range. If the machine already has an actuator, the linear actuator replacement finder can help shortlist replacements.
Two-velocity Gears on Same Shaft Interactive Calculator
Enter input speed and the two pinion/gear tooth-count pairs. The outputs compare alternative Path A and Path B ideal speeds; they are not simultaneous speeds on one rigid shaft, and the tool does not design a selector or tooth geometry.
Equation Used
- The two calculated paths are alternatives selected one at a time; they are not simultaneous angular velocities of one rigid output shaft.
- Each path is one ideal external-gear mesh with compatible pitch and no slip.
- The input pinions share one input shaft and the output gears are represented as loose gears selectively coupled to one output shaft.
- A common module is assumed only for the tooth-count check; module and actual center distance are not inputs.
- Tooth form, interference, undercut, face width, selector or clutch geometry, shift dynamics, backlash, efficiency, torque, power, loads, stress, bearings, lubrication, guarding and suitability are omitted.
Two Alternative Gear Paths
Brown's movement 200 shows one driving wheel associated with two gearing choices on the same shaft and describes the result as two different speeds on that shaft. The short historical caption does not explain a selector.
The calculator therefore makes the necessary kinematic interpretation explicit: two input pinions rotate together, two output gears are loose until a schematic collar selects Path A or Path B, and only one path couples the output shaft at a time.
What This Calculator Represents
Only one path drives the rigid output shaft at a time. The collar is an illustrative way to show that selection; Brown’s caption does not specify this collar, and the calculator does not design a clutch.
The geometry check compares tooth-count sums. With a common module and parallel shaft centers, equal sums give equal nominal center distances.
Ideal Ratios and Tooth-count Check
Path A output = ninzpA/zgA
Path B reduction = zgB/zpB
Path B output = ninzpB/zgB
common-module shared-center condition: zpA+zgA = zpB+zgB
Worked Ideal Example
At 720 rpm, a 20-tooth pinion driving a 40-tooth gear gives Path A a 2:1 reduction and 360 rpm. A 12-tooth pinion driving a 48-tooth gear gives Path B a 4:1 reduction and 180 rpm. Both tooth-count sums are 60, satisfying the nominal shared-center condition for a common module. Tooth form and interference still require separate checks.
Assumptions and Limits
- Calculated: two alternative ideal speed ratios and output speeds.
- Geometry check: equality of tooth-count sums under an explicit common-module assumption.
- Illustrated: an illustrative selector, not a dimensioned clutch.
- Not calculated: module, center distance, tooth form, interference, undercut, selector geometry, shift behavior, torque, power, efficiency, loads, stress, bearings, lubrication, guarding or suitability.
Frequently Asked Questions
Do both output speeds occur simultaneously?
No. One rigid output shaft can have only one angular velocity; the results are alternative selected paths.
Did Brown specify the selector shown?
No. The collar is an illustrative selector; its design is not given in Brown’s caption.
What does equal tooth-count sum prove?
Only that the two pairs can share a center distance under one common module. It does not complete the gear design.
What if the sums differ?
The arithmetic ratios remain independently valid, but the entered pairs do not satisfy that shared-center common-module condition.
Are direction and losses included?
The reported values are speed magnitudes for ideal external meshes; losses are omitted.
Can this design a gearbox?
No.
References
Building or designing a mechanism like this?
Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.