Horse-power Machine: Historical Platform and Gear-Ratio Exercise | FIRGELLI

← Back to Engineering Library

Hiscox’s horse-power machine uses a slatted walking platform carried by an endless chain and rollers to turn a sprocket shaft. The calculator below is a separate single external-gear comparison. It calculates speed ratio, ideal torque ratio and output period, not treadmill motion, animal power or machine capacity.

Horse-power Machine Interactive Calculator

Explore an ideal external gear pair using entered input RPM and tooth counts.

0°

Ideal Pinion Speed
--
Speed Ratio
--
Ideal Torque Ratio
--
Output Period
--

Equation Used

Nout=Nin(Tbull/Tpinion); ideal tauout/tauin=Tpinion/Tbull; output period=60/Nout
Single external gear mesh with the entered bull gear driving the entered pinion. The shafts counter-rotate.
  • Bull gear is the driver and pinion is the driven gear.
  • Compatible involute teeth with the same module or diametral pitch and valid centre distance are assumed but not checked.
  • No slip, mesh loss, backlash, compliance, inertia, transient load or secondary belt/gearing stage.
  • No power source, animal workload, shaft, key, bearing, gear strength, guard, driven-machine or safety model.

The torque tile is an ideal output/input torque ratio under lossless steady power transfer—not usable torque. Input torque, efficiency, tooth geometry, strength and all machine loads are absent.

Related video: geared horse power
Video: Geared horse power by Nguyen Duc Thang (thang010146) on YouTube. This geared example is separate from the chain-and-platform machine described by Hiscox and from the calculator’s single fixed-axis mesh.
Same mechanism and inputs as the interactive calculator.

One ideal external gear mesh

At the pitch point, tangential speeds match. Because pitch radius is proportional to tooth count for compatible gears, a bull gear with Tbull teeth driving a pinion with Tpinion teeth gives Nout/Nin=Tbull/Tpinion. External gears rotate in opposite directions.

Use as a ratio check

The identities check the speed change and opposite rotation of a single external gear pair. The output speeds up when the driver has more teeth, slows down when it has fewer, and matches the input-speed magnitude when the counts are equal. This does not model the historical chain-and-platform machine.

Speed and ideal torque reciprocity

Nout=Nin(Tbull/Tpinion). For lossless steady power, tauin omegaIn=tauout omegaOut, so tauout/tauin=Tpinion/Tbull. Output period is 60/Nout seconds per revolution.

Worked example

A 72-tooth driver turning at 4 rpm and driving an 18-tooth pinion has a 4:1 speed ratio, so the ideal output is 16 rpm and its period is 3.75 s. The ideal output/input torque ratio is 0.25 before losses.

Scope and limitations

Real design requires compatible tooth system, pressure angle and geometry; undercut and contact ratio; materials and heat treatment; transmitted torque and service factor; bending/contact stress and life; lubrication, alignment, backlash, shafts, keys, bearings, housing, guards, overspeed and the complete load cycle.

Questions

Does a 4:1 ratio provide four times the power?

No. Ideal power is conserved; speed rises while torque falls reciprocally.

Is the torque tile available output torque?

No. It is only a dimensionless multiplier; actual input torque and losses are unknown.

Can any tooth counts mesh?

No. Module or diametral pitch, pressure angle, centre distance and tooth-form constraints must also match.

Historical source and calculation basis

Gardner D. Hiscox, Mechanical Movements, Powers, Devices and Appliances, entry 1534, describes an endless-chain walking platform on rollers driving a sprocket shaft. His separate entry 1536 concerns a geared horse-power mechanism.

The calculator represents neither complete assembly. It uses equal pitch-line speeds and ideal power conservation for one fixed-axis external gear mesh. Those identities do not establish available power, tooth strength or equipment capacity.

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: