A hairspring supplies the restoring torque for a mechanical watch’s balance wheel. The spring bends as the balance turns, then releases stored energy as the balance returns. Use this calculator to compare ideal frequency, beats per hour, maximum spring energy and the rate change from a small stiffness adjustment.
Hairspring Interactive Calculator
Explore an ideal linear balance-and-hairspring oscillator, including its natural frequency, watch-convention beats per hour, maximum stored spring energy and the rate change caused by a hypothetical effective-stiffness trim.
Equation Used
- Linear torsional stiffness and small-angle harmonic motion.
- Balance inertia is entered in mg-cm^2 and stiffness in nN-m/rad.
- The entered swing angle sets ideal maximum spring energy but does not change frequency in this linear model.
- No escapement impulse, damping, regulator-pin geometry, terminal-curve elasticity, positional error, temperature, magnetism, shock, friction, wear or manufacturing-tolerance model.
Ideal small-angle linear torsional-oscillator comparison only. Stiffness trim changes the effective torsional stiffness mathematically; it is not a regulator-geometry, temperature, magnetism or service model. The spiral drawing preserves the fixed stud and rotating collet but is not an elastic stress or terminal-curve solution.
How the balance and spring oscillate
The inner end of a hairspring follows the balance staff through a collet. Its outer end is held by a stud. Rotating the balance bends the spring, producing a torque toward the neutral position. In the ideal linear model, restoring torque is proportional to angle and stored energy is proportional to angle squared.
The balance has rotational inertia, so it passes through neutral and bends the spring in the opposite direction. An escapement supplies impulses to replace energy lost in a real watch and links the oscillations to the wheel train. The calculator omits that drive and its losses.
The active spring body, its terminal shape and its attachments affect the real motion. An overcoil raises and redirects the outer end to improve how the spring expands and contracts. Breguet dates its overcoil development to 1795; an overcoil is one spring arrangement, not a feature of every modern hairspring.
Main parts
- Balance: provides rotational inertia.
- Spring body: bends and stores elastic energy.
- Collet and stud: attach the inner and outer ends.
- Regulating system: may adjust effective spring behavior or balance inertia, depending on the movement.
- Escapement: sustains and counts the oscillations in a running watch.
Timekeeping and restoring springs
Mechanical watches and chronometers use a balance-and-spring oscillator as a time reference. Some instruments also use fine spiral restoring springs, but their purpose may be to balance an applied torque rather than sustain a timing oscillation.
Material, temperature response, terminal geometry and the complete movement affect performance. This model takes an effective stiffness as an input; it cannot rank spring materials, certify a chronometer or diagnose a particular watch.
Ideal oscillator equations
f = √(keff/I)/(2π)
T = 1/f
BPH = 7200f
Emax = ½keffθmax²
Rate change = 86400(f/f0 − 1)
I is balance inertia in kg·m², k is torsional stiffness in N·m/rad, δ is the entered percentage trim, and θ is angle in radians. f is full oscillations per second; a watch conventionally counts two beats per oscillation. f₀ is the frequency with the same inertia and nominal stiffness but zero trim.
The input conversion is 1 mg·cm² = 10⁻¹⁰ kg·m² and 1 nN·m = 10⁻⁹ N·m. With stiffness in nN·m/rad, ½kθ² directly gives energy in nJ. Positive rate change means faster than the untrimmed oscillator.
Frequency is independent of amplitude in this linear model. Real hairspring behavior, escapement action and losses can make frequency depend on amplitude. Stiffness Trim is a mathematical comparison, not an instruction to move regulator pins by a particular distance.
Example: a 4 Hz ideal oscillator
Use 10 mg·cm² balance inertia, approximately 631.655 nN·m/rad nominal stiffness, 30° swing amplitude and zero trim.
- Convert inertia to 10⁻⁹ kg·m² and stiffness to approximately 6.31655 × 10⁻⁷ N·m/rad.
- The frequency is approximately 4 Hz, giving a 0.25 second full period and 28,800 beats per hour.
- Convert 30° to π/6 radians. Maximum spring energy is approximately 86.59 nJ.
- At +0.1% stiffness trim, frequency becomes approximately 4.002 Hz and the ideal rate change is +43.19 seconds per day.
At −0.1% trim, the ideal rate change is approximately −43.21 seconds per day. Doubling swing amplitude would quadruple energy at the same stiffness; within the available controls, changing 30° to 15° reduces it to one quarter, about 21.65 nJ. Neither amplitude change alters the calculated frequency.
Comparing time references
| Oscillator | Restoring mechanism | Important distinction |
|---|---|---|
| Balance and hairspring | Elastic torque acting on a rotating balance. | Requires a drive to replace losses; real performance depends on the full movement. |
| Quartz oscillator | Elastic vibration of a piezoelectric crystal. | Uses an electronic circuit; this hairspring model does not predict its frequency stability. |
| Torsion pendulum | Twisting of a suspension member. | Shares the ideal inertia-and-torsional-stiffness equation, but uses different geometry and suspension. |
Frequently asked questions
What does one beat mean?
A beat is a half oscillation in the watch convention used here. A 4 Hz balance completes four full oscillations and eight beats per second, or 28,800 beats per hour.
Why does Swing Angle change energy but not frequency?
The assumed torque is linear in angle. Frequency depends on stiffness divided by inertia, while maximum spring energy depends on amplitude squared. This does not prove that a real watch is perfectly isochronous.
What does Stiffness Trim represent?
It multiplies the nominal stiffness by 1 plus the entered percentage divided by 100. It does not model a regulator, spring length, material change or temperature change.
Is Rate Change the accuracy of my watch?
No. It compares the trimmed ideal oscillator with its untrimmed version. A zero result means zero entered trim, not zero error against a time standard.
Is only the terminal curve storing energy?
No. Elastic bending of the active spring stores energy. The terminal curve influences how the spring deforms and where it is attached.
Does the animation show an actual elastic spring shape?
No. Its spiral connects a fixed outer stud to a rotating inner collet. The intermediate curve illustrates that connection and does not solve spring stress or terminal geometry.
Does playback run at the calculated frequency?
No. One displayed oscillation takes six seconds so the motion can be inspected. Numerical frequency and beats per hour still use the entered inertia and stiffness.
Can a rate change diagnose a repair problem?
No. Temperature, magnetism, rubbing, escapement effects and positional errors are not inputs. Diagnosis requires measurements of the actual movement.
Spring energy and drive energy
The displayed energy is the maximum energy stored in the ideal hairspring at a turning point. A real escapement replaces energy lost during motion; it does not supply this full stored energy anew at every swing. Damping and escapement inputs are needed to estimate drive power.
References and further reading
Breguet: development and attachment of the balance spring. Historical context for the overcoil, distinct from the ideal oscillator calculation.
Building or designing a mechanism like this?
Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.