Fusee: Endpoint Radius and Torque Comparison | FIRGELLI

← Back to Engineering Library

A fusee uses a changing chain moment arm to compensate for changing mainspring torque. This calculator compares two spring-torque endpoints and finds the corresponding endpoint radius ratio for an ideal constant-radius barrel. It does not calculate the complete fusee profile or a clock’s timekeeping accuracy.

Fusee Torque Equalization Interactive Calculator

Enter full-wind torque, run-down torque and the full-wind fusee radius. Compare the ideal run-down radius, radius ratio and torque-radius product.

Run-down Radius
--
Radius Ratio
--
Const Product
--
Torque Drop
--

Equation Used

r_low = r_full * T_full / T_low; K = T * r = constant

The fusee keeps drive approximately constant by increasing its effective radius as mainspring torque falls. For endpoint sizing, the torque-radius product is held constant, so the run-down radius equals the full-wind small radius multiplied by the full-to-low torque ratio.

  • Fusee radius is inversely proportional to mainspring torque.
  • Endpoint torques represent full wind and run-down states.
  • The barrel radius is constant. Friction and changes in effective chain-contact radius are omitted; two endpoints do not define the intermediate profile.
Spring barrel and grooved fusee 123
1 — Constant-radius spring barrel. 2 — Variable-radius fusee. 3 — Connecting chain. The barrel draws chain from the fusee as the spring runs down. For the usual falling spring torque, the chain moves toward the larger fusee radius. The chain moment arm compensates for the lower tension. This simplified perspective shows a tapered form, not a measured clock profile. Use the interactive animation above to follow the motion.

A changing chain moment arm

A chain connects the mainspring barrel to the grooved fusee. As the spring runs down, the barrel draws chain from the fusee. The chain acts at progressively larger fusee radii when compensating a falling spring torque.

The fusee turns the going train through its drive wheel. Winding reverses the chain transfer. Some constructions include a maintaining-power arrangement so the train continues receiving drive during winding; that is a separate function from the varying radius.

The animation shows a spring barrel beside a grooved fusee, with a chain spanning their tangent contact points. The two entered torque endpoints set the top and bottom fusee radii. Equal torques give a cylinder; rising torque reverses the taper. Contact moves between the endpoints and back to make the changing moment arm visible. The straight taper, six illustrated wraps and transfer pace are schematic, not a profile fitted to a measured spring curve or a calculation of chain length. The barrel is drawn at an assumed 15 mm radius; this does not add an output-torque result to the calculator.

Horological examples

Fusee-and-chain transmission is associated with spring-driven timekeepers and remains in selected modern watches. A. Lange & Söhne describes both its changing moment arm and the separate mechanism used to maintain drive during winding. Royal Museums Greenwich also holds fusee-chain components in its horological collection.

These examples establish the mechanism’s use, not a universal rate accuracy, service interval or improvement for every escapement. The calculator contains no escapement, oscillator or timekeeping model.

Endpoint radius relation

For an ideal fixed barrel radius r_b, chain tension is F = T_s/r_b and fusee output torque is T_out = T_s r_f/r_b. Therefore constant output requires T_s r_f to remain constant. The calculator applies r_run = r_full T_full/T_run.

Const Product is K = T_full r_full, displayed in mN·m·mm. This product is not output torque. To obtain output torque in mN·m, divide K by the barrel radius in millimeters. Barrel radius is not an input here, so neither output torque nor chain tension is an output.

Radius Ratio is r_run/r_full. Torque Drop is 100(T_full − T_run)/T_full. Equal torques give equal radii and zero drop. A greater run-down torque gives a negative drop and a radius ratio below one; that is a rising-torque comparison rather than the usual falling-torque case.

The full spring curve and the chain’s winding geometry are needed for a complete profile. Matching only two endpoints does not guarantee constant torque between them.

Example: endpoint compensation

The defaults are 60 mN·m full-wind torque, 25 mN·m run-down torque and 5 mm full-wind radius. The run-down radius is 5 × 60/25 = 12 mm. Radius Ratio is 2.4:1, Const Product is 300 mN·m·mm and Torque Drop is 58.3%.

If a separate barrel radius of 15 mm is assumed, those endpoints give 300/15 = 20 mN·m output torque. Chain tension is 60/15 = 4 N at full wind and 25/15 = 1.667 N at run-down. The unit identity mN·m = N·mm makes those numerical divisions valid.

For another hypothetical target of 22 mN·m and a 15 mm barrel, spring torques of 70, 50 and 30 mN·m require fusee radii of 4.714, 6.600 and 11.000 mm. This is an algebraic example; the radius control advances in 0.1 mm steps. It establishes no eight-day run or rate accuracy for a named clock.

Across the accepted inputs, the endpoint radius ratio spans 0.667:1 to 6.667:1 and calculated run-down radius spans 2.667–66.667 mm. Torque Drop spans −50% to 85%. These input bounds are not manufacturing or packaging limits.

What the endpoint calculation leaves out

Compensation depends on the spring’s actual torque curve and the effective chain moment arm. Losses, chain seating and dimensional errors can change the delivered torque. A fixed percentage tolerance cannot be assigned without the movement and measured data.

A going barrel transfers spring drive without the fusee’s variable radius. A maintaining-power device keeps drive available during winding. A remontoire stores and replenishes energy in another stage. These are different functions, and the endpoint relation does not choose between complete clock designs.

The tool does not diagnose rate variation, chain damage or a replacement spring. Conservation and repair decisions for an old movement require examination of its actual construction and condition.

Frequently asked questions

Is Const Product the torque delivered to the train?

No. Its units are torque times length. Divide it by the constant barrel radius to obtain ideal output torque in consistent units.

Why does the fusee radius grow as spring torque falls?

With a constant barrel radius, lower spring torque gives lower chain tension. A larger fusee moment arm compensates for that reduction.

What if run-down torque is greater than full-wind torque?

The radius ratio is below one and Torque Drop is negative. The animation shows a reversed taper with a smaller run-down radius. This illustrates the entered rising-torque comparison rather than a typical mainspring run-down.

Do two endpoints define the entire cone?

No. The full spring torque curve and winding geometry are required to determine the intermediate profile.

Does the chain link pitch have to equal the axial groove pitch?

They are different geometric quantities. Chain dimensions and groove geometry must suit the actual assembly; this calculator supplies no pitch or clearance design.

Does every fusee have the same maintaining-power mechanism?

No. Maintaining drive during winding is a separate feature whose construction depends on the movement.

Can I infer seconds-per-day accuracy from the radius ratio?

No. Oscillator and escapement behavior, losses and operating conditions are not included.

Can this select a replacement mainspring?

No. A replacement must suit the movement and its working range. Endpoint comparison alone does not establish compatibility.

Fusee references

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: