The double-cylinder planer described by Hiscox is a lumber-working machine. A board passes forward through a roughing cutter and a finishing cutter in the same pass. The animation shows that sequence in a functional side section, with feed rolls carrying the stock through both cutterheads.
Double Cylinder Planer Interactive Calculator
Model the lumber planer shown by Hiscox: a forward-fed board receives a roughing cut and a finishing cut. Set stock dimensions, allowances and feed speed to calculate thickness, material removal and board-length feed time.
Equation Used
- Uniform rectangular stock and specified full-width cut allowances.
- The board moves in one direction through both stages.
- Thickness and cut depths share one drawing scale; other geometry is schematic.
- Volume refers to solid material removed, not loose chip volume.
- Zero feed speed gives zero removal rate and no finite feed time.
- Guards are cut away in the illustration to expose the mechanism.
This through-feed lumber planer makes two cuts in one forward pass. Feed time covers one board length; it excludes machine spacing and handling.
One feed direction, two cutting stages
The feed rolls carry the board to the right. The first rotating cylinder removes the entered roughing depth. The second removes the finishing allowance from the already-roughed surface. The lower board face rides along the common bed.
Each head is drawn with cutting edges rotating against the feed direction at contact. Its lowest cutting point defines the surface left behind it. Where the board first enters a head, the displayed material boundary follows the circular cutting envelope rather than jumping through the cutter.
The historical illustration includes a detailed drive train. The side section focuses on the cutters and feed rolls; the drive gears are omitted. Housings are shown in section to make the cutting action visible.
A lumber-sizing calculation
Enter board length and width, starting thickness, the two cut depths, and forward feed speed. The calculator returns finished thickness, removed material volume, removal rate during full-width engagement, and the time needed to advance one board length.
Lumber moves continuously through the two cutters in one direction. The feed calculation therefore uses forward travel only.
Thickness, material volume and feed time
The total depth removed is a=a1+a2, so finished thickness is t−a. For length L in metres and width w and depth a in millimetres, removed volume is Lwa/1000 litres.
At feed speed v in m/min, advancing one board length takes 60L/v seconds. At zero feed speed no finite time is assigned.
During full-width engagement, material-removal rate is vwa cm³/min. This is an ideal geometric rate, not a measure of required spindle power or permissible chip loading.
The time result does not include the separation between cutterheads, lead-in distance, gaps between boards or handling. Those dimensions are not inputs, so the result should not be described as total machine occupancy time.
A 3.2 m board with two allowances
For a 150 mm wide board initially 30 mm thick, a 2 mm roughing cut followed by a 0.5 mm finishing cut leaves 27.5 mm thickness.
The two cutters remove a total of 1.20 L of solid wood volume along a 3.2 m board. At 15 m/min, feed travel equal to the board length takes 12.8 seconds, and full-width engaged removal is 5,625 cm³/min.
Increasing width changes removed volume and removal rate. Increasing length changes total removed volume and board-length feed time. Changing starting thickness changes final thickness, while the selected cut allowances determine removal.
Use the results as geometry and timing
The calculator does not select a suitable cutter rpm, tooth count, feed per knife, motor power or permissible cutting depth. Those depend on the actual machine, cutting tools, timber and operating conditions.
The side view uses entered thickness and cut depths for the material profile. Board length, cutter size, knife detail and playback timing are schematic. Width is perpendicular to this view and is used in the volume calculation.
A zero cut depth leaves that cutter tangent to the existing surface. If both cuts are zero, removed volume and removal rate are zero. Feed can still advance a board without removing material.
Double-cylinder planer questions
Are these hydraulic cylinders?
No. In this historical lumber machine, the cylinders are rotating cutterheads.
Where is the return stroke?
There is none in the modeled process. The board travels forward through both heads.
Does 12.8 seconds mean the entire board has cleared both cutters?
No. It is the time for feed travel equal to one board length. Machine spacing is not included.
Why does width not change the side-view thickness?
Width runs out of the drawing plane. It changes the removed-volume and removal-rate results.
What happens at zero feed?
Playback stops, rates are zero and feed time is reported as stopped. Positions remain inspectable.
Reference
Hiscox, Mechanical Movements, Powers, Devices and Appliances, mechanism 1431, printed page 343 (PDF page 353): a double-cylinder lumber planer taking rough and finishing cuts in one pass.
Building or designing a mechanism like this?
Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.