Double Conic Rope Drum Mechanism Explained: How It Works, Parts, Torque Formula and Uses

← Back to Engineering Library

A double-conic rope drum has a changing winding radius, increasing toward its middle and decreasing toward the opposite end. Hiscox illustrates it for winding engines and as a spinning-mule fusee. The animation shows the tapered body and a rope following its helical groove. The calculator compares a specific static endpoint balance; it does not design a complete mine hoist.

Double Conic Rope Drum Interactive Calculator

Inspect a grooved double-conic drum and compare static endpoint torques. Equal suspended mass is assumed on both sides; the heavy endpoint includes one full hanging rope.

0°

Rope linear mass
--
Heavy endpoint mass
--
Endpoint balance R/r
--
Equal-radius imbalance / heavy torque
--

Equation Used

μ=1000M/L; R/r=(P+M)/P; equal-radius imbalance fraction=M/(P+M).
M and P are tonnes. P is present on both sides. Shaft depth changes kg/m when total rope mass is held fixed.
  • Equal suspended mass on both sides.
  • Heavy endpoint adds one full hanging rope.
  • No losses, acceleration, inertia or rope elasticity.
  • Normalized radii and representative groove count in the construction view.

Static endpoint comparison only; no full-cycle hoist, motor or drum-capacity rating.

Same mechanism and inputs as the interactive calculator.

A changing rope lever arm

Rope tension produces shaft torque equal to tension multiplied by effective winding radius. A tapered drum changes that lever arm as the rope occupies different axial positions. The construction view rotates a fully wrapped illustrative rope with the drum so the changing radius and groove can be inspected. It does not animate cages or claim to solve payout through a complete winding cycle.

The historical figure supplies no drum diameter, groove pitch or force rating. This drawing uses a symmetric straight taper and a representative six-turn groove. Maximum radius is normalized for display; the minimum is calculated from the endpoint balance ratio. Bearings and shaft are illustrative.

The separate force diagrams compare a heavy side on small radius r with a lighter side on radius R. They are equivalent lever-arm diagrams, not two extra hoisting drums. The common suspended mass P is included on both sides; only the heavy endpoint has the entered full rope mass M.

Historical use and scope

The cited historical reference identifies winding-engine and spinning-mule uses. A varying radius is useful when the desired relationship between tension, torque or speed changes with rope position.

Use this calculator to compare rope linear mass and one static radius ratio. It cannot establish the required drum profile, groove count, rope capacity, motor power or braking duty for an installation.

Static endpoint calculation

Enter shaft length L in meters, one full hanging-rope mass M in tonnes, and equal suspended mass P on each side in tonnes. Rope linear mass is 1000M/L kg/m. The heavy endpoint mass is P+M; the light endpoint mass is P.

Static balance requires (P+M)gr=PgR, so R/r=(P+M)/P. Gravity and tonne-to-kilogram conversion cancel in this ratio. With equal radii instead, net torque divided by the heavy-side torque is M/(P+M); the fourth output expresses this fraction as a percentage.

This percentage is not a full-cycle torque swing or an energy saving. Absolute torque needs an actual radius. A changing-radius drum also changes rope speed for a given shaft speed, so endpoint balance alone does not determine a feasible two-rope trajectory.

Example: equal 24-tonne suspended masses

With L=2000 m, M=24 t and P=24 t, rope linear mass is 12 kg/m. The heavy endpoint has 48 t and the light endpoint 24 t. Their balance ratio is R/r=2.

If a small radius of 1 m is chosen solely to illustrate torque, the large radius is 2 m. Heavy-side torque is 48000×9.81×1=470880 N·m; light-side torque is 24000×9.81×2=470880 N·m. The calculator does not select that 1 m radius.

At equal radii the imbalance fraction is 24/48=50%. Changing shaft depth while holding total rope mass fixed changes kg/m but not the endpoint mass ratio. Changing rope or suspended mass changes the ratio and the visual taper.

Endpoint balance is not a hoist design

The three inputs do not define acceleration, empty-cage mass distinct from loaded-cage mass, groove pitch, layer build-up, rope stretch, bearings, drum inertia, braking or a motor torque-speed curve. No absolute drum dimensions or capacity rating are inferred.

The endpoint comparison assumes equal suspended mass on both sides, with the full hanging rope added to one side. Its balance ratio describes those two static conditions. A complete hoist design also needs the winding profile, changing rope lengths, acceleration, braking and motor duty.

Double-conic drum questions

Why does depth change only rope linear mass?

Total rope mass is an independent input. If the same mass is spread over a different length, kg/m changes while endpoint masses do not.

Why does the diagram become sharply tapered at a high ratio?

The displayed maximum radius stays fixed while the minimum follows r=R/(R/r). This illustrates the entered ratio without asserting that such a drum is practical.

Does the rotating view show rope payout?

No. It is an unloaded construction inspection, with the illustrative wrapped rope rotating with the drum.

Is the percentage a power saving?

No. It compares static torques at equal radii in the defined endpoint example.

Construction reference

Gardner D. Hiscox, Mechanical Movements, Powers and Devices, printed page 323, figure 1320 (PDF page 333). The illustration shows a grooved double-conic drum. Its proportions are illustrative, while the calculator uses the static balance assumptions stated above.

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: