A crank-rod head adjustment can take up clearance in a jointed bearing brass inside a trunk piston. The historical arrangement illustrated here uses a long screw acting on the bearing cap. This is a bearing adjustment, not a rule for changing piston-to-head clearance by removing big-end shims.
Related actuator design tools
This tool compares bearing clearances; it does not design an actuator to adjust a bearing. For a separate actuator-driven linkage, calculate its required force, travel and mounting geometry through the full motion.
For crank motion, review the throw radius and the changing angle between the actuator and driven link. Those two details decide whether the actuator is pushing efficiently or fighting the geometry.
A crank or cam may tolerate continuous rotation through a difficult part of the cycle, while a linear actuator has defined end positions and internal limits. That difference matters when the mechanism needs repeatability or must not drive into a hard stop.
- Map actuator stroke to the actual output travel before choosing a model.
- Check for binding, changing leverage, and peak load near the ends of travel.
- Decide whether timed motion is acceptable or position feedback is required.
For a FIRGELLI design review, calculate the load case with the FIRGELLI actuator force calculator and plan the switching or controller arrangement with the linear actuator wiring diagram generator. If an actuator or cylinder is already installed, the linear actuator replacement finder helps keep the comparison tied to real dimensions.
Crank-rod Head Adjustment Interactive Calculator
Compare measured rod-head bearing clearance before and after take-up. Set the applicable lower and upper limits and inspect the jointed bearing in the piston section.
Equation Used
- All clearance quantities refer to the same measured diametral bearing clearance.
- Take-up is a measured reduction in that clearance.
- User-entered limits are comparison values, not validated service specifications.
- No inferred relation between shim thickness, screw movement and piston-to-head gap.
- The mechanism drawing is schematic, with clearances magnified below.
Measured take-up is the reduction in bearing clearance, not shim thickness or screw travel.
Jointed brass inside a trunk piston
The piston contains the small-end joint of the connecting rod. A hinged bearing cap and long adjusting screw provide a way to take up the brass around the joint. During operation the adjustment remains fixed while the rod changes angle and the piston reciprocates.
The upper animation shows that arrangement schematically with a connected slider-crank drive. The lower diagrams compare initial and remaining diametral clearance, with the gaps magnified so small changes can be seen.
Clearance comparison
This tool compares an initial measured bearing clearance with a measured amount of take-up. Enter the lower and upper limits for the particular joint from its applicable specification. The example limits are calculation inputs, not recommendations for a named engine.
Measured take-up arithmetic
If initial diametral clearance is C₀ and measured clearance reduction is ΔC, the resulting clearance is C₁=C₀−ΔC. The signed change is −ΔC. Margin to an entered band is min(C₁−Cmin, Cmax−C₁); the amount outside the band is max(Cmin−C₁, C₁−Cmax, 0).
When the lower limit exceeds the upper limit, the band comparison is unavailable. A negative remaining clearance means interference in this arithmetic model and is displayed explicitly. The calculator does not convert screw rotation or removed shim thickness into clearance change.
Example measurements
An initial measured clearance of 0.0040 in and measured take-up of 0.0020 in leave 0.0020 in. Against an entered band of 0.0010–0.0030 in, the nearest-limit margin is 0.0010 in and the outside-band amount is zero.
These values demonstrate the calculation. They are not factory clearances, tightening torques or instructions for a particular machine.
Separate the different clearances
Joint bearing clearance, piston-to-head clearance, screw travel and shim thickness are different measurements. Their relationship depends on the actual construction. Removing equal shims from opposite sides of a cap does not justify simply adding their thicknesses as a rod-length change.
The illustration does not assess wear shape, bearing crush, alignment, lubrication or bolt loading. The displayed margin only compares the numbers entered by the user.
Rod-head adjustment questions
Does this calculate piston-to-head clearance?
No. It compares measured diametral clearance at the rod-head bearing.
Is measured take-up the amount of shim removed?
No. Enter the measured reduction in the bearing clearance. The calculator does not assume a shim-to-clearance conversion.
Are the example limits safe for my engine?
They are illustrative values. Use the applicable limits for the actual bearing and machine.
Why can the resulting clearance be negative?
The entered take-up exceeds the initial clearance. A negative remaining clearance indicates interference in this arithmetic model.
Reference
Gardner D. Hiscox, Mechanical Movements, Powers, Devices and Appliances, 1901 edition, printed page 125, figure 450: the jointed-brass adjustment for a trunk piston. The calculation compares measured clearances; it does not convert screw travel into a clearance change.
Continue exploring engineering
Find another tool, explore an animated mechanism, or browse resources by subject.
Building or designing a mechanism like this?
Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.