Brown Movement 27: Three-Roller Carrier and Radial-Groove Wheel

← Back to Engineering Library

Brown movement 27 shows three rollers attached to a triangular carrier engaging radial grooves in a larger wheel. Explore the arrangement and calculate the range of roller-center distances from the larger wheel center.

Three-Roller Radial-Groove Geometry Calculator

Enter illustrative dimensions for the carrier and grooved wheel. The worksheet reports the fixed three-roller pitch and the exact minimum and maximum roller-center radius implied by the declared center offset and roller orbit. For a working six-groove illustration, set center offset equal to roller orbit and choose a wheel radius large enough to contain the rollers.

0°

Attached carrier rollers
--
Carrier roller pitch
--
Minimum roller-center radius
--
Maximum roller-center radius
--

Equation Used

roller pitch=360°/3=120°; minimum center radius=|a-e|; maximum center radius=a+e
Brown illustrates three carrier rollers engaging radial grooves. This viewer uses six equally spaced grooves and equal center offset and roller orbit. Those proportions make the roller centers align with the grooves throughout a cycle. Other dimensions are shown as an outline preview.
  • Three roller centers are equally spaced on a declared circular orbit around the triangular carrier center.
  • The carrier and larger wheel centers have a declared fixed offset.
  • The radius bounds follow directly from the triangle inequality for the declared offset and orbit.
  • The animation demonstrates ideal roller-center alignment. Contact forces, groove-flank design, friction, torque capacity, wear and service life are not calculated.

The three roller centers remain 120 degrees apart. Equal center offset and roller orbit give continuous alignment with six radial grooves. In this ideal construction the wheel rotates half as fast as the carrier.

Three carrier rollers enter radial grooves

Brown's 1868 description identifies a smaller triangular wheel and friction rollers attached to it. Their movement in radial grooves drives the larger wheel. The plate shows the carrier and wheel on offset centers.

The animation shows a six-groove construction with three rollers spaced 120° apart. When the center offset equals the roller orbit, the orbit circle passes through the larger wheel's center. The inscribed-angle relationship makes each roller's radial direction turn at half the carrier speed; the three radial directions are separated by 60° modulo a half-turn. These are illustrative proportions, not dimensions measured from Brown's plate.

Explore the carrier and grooved wheel

Use the viewer to identify the two wheel centers, the triangular carrier, its three attached rollers and the larger wheel's radial grooves. The viewer examines the historical arrangement without assigning it to a particular modern machine.

Declared carrier geometry only

roller pitch=120°; rmin=|a-e|; rmax=a+e

These identities describe the three roller centers relative to the larger wheel center. They do not produce a transmission ratio.

Illustrative carrier-geometry example

For a 45 mm center offset and a 70 mm roller-center orbit, the three attached rollers remain 120° apart. A roller center can lie from |70-45|=25 mm to 70+45=115 mm from the larger wheel center as the carrier turns. These example dimensions are illustrative rather than measurements from the historical plate.

Carrier geometry and complete engagement

The radial-distance limits follow from the offset between wheel centers and the roller-center orbit. In the equal-offset-and-orbit example, the three roller centers remain on the six radial groove axes and the wheel turns once for two carrier turns. The wheel radius must also contain the full roller envelope. Groove width, finite contact areas, clearances and shaft supports require further design before making a physical drive.

Movement 27 questions

Are the three rollers different selectable diameters?

No. Brown describes friction rollers attached to the smaller triangular wheel.

Does Brown publish a speed ratio?

No. The brief caption supplies no dimensions or velocity law.

Which dimensions give a working illustration?

Set center offset equal to roller orbit, and make the wheel radius greater than twice the orbit plus half the roller diameter and a small clearance. Incompatible settings show an outline geometry preview.

Historical movement references

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: