Gear-Tooth Higher Pair: Involute Gear Geometry Calculator | FIRGELLI

← Back to Engineering Library

Meshing gear teeth form a higher pair: their ideal contact is along a line or at a point rather than across conforming surfaces. This page shows an external involute spur-gear pair and calculates its nominal ratio, output speed, centre distance and pitch-line speed. Change pressure angle to see the base circles and line of action change; that control does not change these four numerical results.

Gear-tooth Higher Pair Interactive Calculator

Calculate nominal external spur-gear ratio, driven speed, standard center distance and pitch-line speed while inspecting pitch, base and nominal addendum-circle geometry.

0°

Reduction
--
Driven Speed
--
Centre Distance
--
Pitch Speed
--

Equation Used

pitch diameter d = module m x tooth count z; ratio i = z2/z1; ideal n2 = n1/i; nominal center distance a = (d1+d2)/2; pitch-line speed v = pi d1 n1/60,000
Dimensions use millimetres and speed uses rpm. The pressure-angle input affects the displayed base circles and nominal line of action but not the four reported scalar outputs.
  • External standard-module spur gears at nominal center distance.
  • Both gears use the same entered module and pressure angle.
  • Ideal rigid conjugate action with no slip at the pitch point.
  • No profile shift, undercut/interference, contact-ratio, backlash, load, strength, efficiency, noise, lubrication or life model.

Nominal ideal geometry and no-slip speed kinematics only. Module, tooth counts and pressure angle do not by themselves establish interference-free or manufacturable teeth, adequate contact ratio, backlash, load capacity, efficiency, noise, lubrication or life.

Supplementary lesson on gear stresses
Video: AGMA Bending & Contact Stress & Strength for Spur Gears | Lewis Equation | Tooth Pitting & Fatigue on YouTube. This supplementary lesson discusses tooth stress and strength, which are outside the calculator above.
Same mechanism and inputs as the interactive calculator.

Higher-pair tooth contact

Two external involute gears contact along a common line of action tangent to their base circles. At the pitch point, the pitch-circle tangential velocities match; the gears therefore rotate in opposite directions with speed magnitude inversely proportional to tooth count.

The animation constrains its red marker to the finite nominal path between addendum-circle intersections. The visible tooth marks are schematic and are not generated manufacturing profiles.

Nominal geometry exploration

The calculator is useful for checking elementary module, ratio, center-distance and pitch-line-speed arithmetic. A real gear set additionally requires an identified tooth system, profile-shift and interference checks, contact ratio, backlash and tolerance selection, materials, heat treatment, face width, shafts, bearings, lubrication, load spectrum and thermal analysis.

Standard reference dimensions and ideal speed

For module m and tooth count z, reference pitch diameter is d=mz. For two external gears with the same module, nominal center distance is a=(d1+d2)/2. Ratio magnitude is i=z2/z1 and ideal driven speed is n2=n1/i in the opposite direction. Driver pitch-line speed is v=pi d1 n1/60,000 when d1 is in millimetres and n1 is rpm.

For entered pressure angle phi, each displayed base-circle radius is rb=r cos(phi). This visual construction does not prove adequate contact ratio or freedom from interference.

Reading the nominal result

For module 2 mm, 20 driver teeth, 80 driven teeth and 3,000 rpm, pitch diameters are 40 and 160 mm, ratio is 4:1, ideal driven speed is 750 rpm, nominal center distance is 100 mm and driver pitch-line speed is 6.28 m/s.

What the results mean

The pressure-angle control changes the reference base circles and line-of-action orientation, but the calculator does not generate exact involute tooth flanks or evaluate undercut, tip interference, transverse contact ratio or operating pressure angle away from nominal center distance. Reported speed is ideal and excludes losses and deflection.

Frequently asked questions

Why does pressure angle change the drawing but not the numbers?

Pressure angle determines the base-circle radii and line-of-action orientation. At the nominal centre distance used here, ratio, driven speed, centre distance and pitch-line speed depend on the other inputs.

Does matching module guarantee a usable mesh?

No. The pressure angle and tooth system must also match, and geometry still requires interference, contact and tolerance checks.

Is the red dot an exact loaded contact solution?

No. It is a schematic point constrained to the nominal path of contact; tooth deformation and load sharing are not modeled.

Can the output turn faster than the input?

Yes. If the driven gear has fewer teeth than the driver, the ratio is below 1 and the driven speed is higher. External gears rotate in opposite directions.

Does pitch-line speed rate the gear set?

No. It is a kinematic quantity, not a capacity, noise, lubrication or life rating.

Gear-manufacturer technical references

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: