Fiddle Drill: Bow Travel and Alternating Rotation Calculator | FIRGELLI

← Back to Engineering Library

A fiddle drill turns a spindle by moving a bowstring back and forth around it. The spindle reverses direction with each stroke. Compare bow travel, contact diameter and stroke rate to calculate ideal turns per stroke and average rotational travel, then apply an assumed grip factor to explore lost motion.

Fiddle Drill Interactive Calculator

Vary spindle diameter, bow stroke, stroke rate, and loaded grip to see revolutions per stroke and drill RPM.

Rev / Stroke
--
No-Slip RPM
--
Loaded RPM
--
Loss
--

Equation Used

rev_per_stroke = L / (pi*d); RPM = rev_per_stroke * strokes_per_sec * 60 * eta

One one-way stroke produces L/(πd) turns without slip. The rate input counts one-way strokes per second, so a full back-and-forth cycle counts twice. RPM here is average absolute rotational travel per minute, not steady one-direction rotation or instantaneous speed. Loaded Grip is an assumed multiplier, not a prediction of cutting performance.

  • Bowstring wraps once around the spindle.
  • No-slip geometry sets revolutions per stroke.
  • Loaded grip is a user-selected percentage of ideal motion; actual losses are not calculated.
  • The illustrated bidirectional bit can cut on both strokes; cutting depends on the actual edge geometry.
Watch the Fiddle Drill in motion
Video: #124 Fiddle Bow Drill Alternating Rotary Motion – 507 Mechanical Movements 3D Animation on YouTube. Related demonstration of the bow-driven drill.
Bow-driven drill with a cord around the spindle 123
1 — Bow. 2 — Cord and spindle. 3 — Bit and workpiece. Moving the bow pulls its cord around the spindle. Each return stroke reverses the drill; axial pressure is supplied through the upper support. Use the interactive animation above to follow the motion.

Bow travel becomes alternating rotation

The bow moves the string across the spindle or a pulley attached to it. When the string grips without sliding, each circumference of string travel produces one spindle turn. Reversing the bow reverses the spindle.

The upper support locates the spindle while the bit engages the work below. The drive supplies alternating rotation; the operator separately controls axial feed. A bit intended to cut in both directions needs the corresponding cutting-edge geometry.

For this calculation, diameter means the contact diameter where the string drives the spindle. A separate drive pulley therefore requires its diameter rather than the drill-bit diameter.

A hand-driven drilling motion

The fiddle drill illustrates how a simple string drive converts a reciprocating hand motion into alternating rotation. Henry T. Brown includes it as movement 124 in Five Hundred and Seven Mechanical Movements.

The geometry calculation helps compare bow travel and spindle diameter. It does not choose a cutting speed, bit size, string tension or material. Hole quality also depends on the bit, support, alignment, workholding and operator feed.

Turns per stroke and average motion

With one-way bow travel L and contact diameter d in the same length units, turns per stroke are n = L/(πd). If f counts one-way strokes per second, ideal absolute rotational travel is 60nf revolutions per minute.

A full back-and-forth cycle contains two one-way strokes. For one complete cycle per second, enter f = 2. Over equal forward and return strokes, net signed rotation is zero even though the spindle has travelled through many turns.

The Loaded RPM output multiplies the ideal result by the entered grip percentage divided by 100. It does not calculate friction, cutting torque or the variation in speed during a stroke.

Example: 250 mm travel and 3 mm diameter

One 250 mm stroke around a 3 mm contact diameter gives 250/(π × 3) = 26.53 turns. At two one-way strokes per second, average absolute rotational travel is 26.53 × 2 × 60 = 3,183.10 revolutions per minute.

With an assumed grip factor of 80%, the Loaded RPM display becomes 2,546.48 and the loss display is 20%. These are model outputs, not a recommended drilling speed or a measured loss.

At the same stroke rate and travel, doubling contact diameter to 6 mm halves the ideal result to 1,591.55. Instantaneous speed still rises and falls as the hand reverses the bow.

Diameter, travel and grip

A smaller contact diameter produces more turns for the same bow travel, while a larger diameter produces fewer. Longer strokes or more strokes per second increase accumulated rotational travel.

Those geometric changes do not establish usable cutting torque or string grip. The model also omits spindle bending, bearing friction and runout. Compare an actual tool under its intended conditions before treating the assumed grip factor as measured performance.

Frequently asked questions

Does Stroke Rate count full cycles?

No. It counts one-way strokes. One forward stroke plus one return stroke is two strokes, so one complete cycle per second is entered as 2.

Why is RPM not a steady spindle speed?

The spindle reverses each stroke and slows during reversal. The result describes average absolute rotational travel over time.

Which diameter should I enter?

Use the diameter at the string contact. If a pulley drives the spindle, use that pulley diameter, not the drill-bit diameter.

Does Loaded Grip calculate the effect of cutting force?

No. It simply scales ideal motion by an assumed percentage. The calculator has no force, torque or friction model.

Can an ordinary one-direction drill cut on both strokes?

The bow reverses the spindle. Cutting on both strokes requires suitable cutting edges; a bit designed for one direction does not automatically gain that ability.

Does more calculated RPM mean better drilling?

No. The appropriate cutting conditions depend on the bit and material. This tool compares motion geometry, not cutting quality or tool life.

Reference

Henry T. Brown, movement 124: the fiddle drill and its alternating rotary motion.

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: