Endless-chain Maintaining Power (clock) Mechanism Explained: Parts, How It Works, and Uses

← Back to Engineering Library

Endless-chain maintaining power keeps a weight-driven clock connected to its driving weight while that weight is raised. A movable pulley carries the main weight between the going-train wheel and a separate winding wheel. A lighter suspended pulley keeps the return side of the closed chain tensioned.

Endless-chain Maintaining Power Interactive Calculator

Compare the main driving mass with the return-chain tension weight. Watch the closed-chain arrangement keep the drive wheel moving while the main weight is wound upward.

0°

Mass Ratio
--
Counter Share
--
Counterweight force
--
Main weight force
--

Equation Used

Mass ratio=M/mc; counterweight share=100mc/M; weight forces=Mg and mcg.
Mass inputs control weight labels and all four comparisons. The routing illustration preserves total chain length and continuous drive rotation.
  • Masses converted to kilograms before force calculation.
  • Standard gravity 9.80665 m/s².
  • Weight forces shown, not available drive torque.
  • Expanded ideal chain geometry with prescribed accelerated motion.

Weight forces are not individual strand tensions. Sequence is accelerated; clock rate and available torque are not calculated.

Same mechanism and inputs as the interactive calculator.

The driving weight remains connected

During normal running, the winding wheel is held by its click. The main weight descends gradually and pulls the drive wheel forward. During winding, the operator turns the winding wheel to raise the main weight while the drive wheel continues advancing.

The weight is not detached from the going train during this operation. That continuous connection supplies maintaining power. The lighter return weight keeps the loop tensioned; it is not a substitute driving weight that alone takes over the clock.

The animation expands the routing so all four pulleys are visible. The upper two shafts are fixed. Both lower pulleys move with their suspended weights. The closed chain has constant length, runs tangent to the pulleys, and changes position continuously during the winding sequence.

Compare the two weights

The calculator uses two mass inputs to show four results: main-to-counterweight mass ratio, counterweight percentage and the gravitational force of each weight. Changing either input updates the matching weight label in the animation.

The picture shows an accelerated running-and-winding sequence. It does not model an escapement or predict how fast a real clock runs. A clock’s operating speed is regulated by its oscillator and escapement, not obtained by dividing these two masses.

What the mass calculator calculates

Convert the counterweight from grams to kilograms: mc=mc,g/1000. The mass ratio is M/mc, and the counterweight share is 100mc/M percent. The two weight forces are Mg and mcg, using g=9.80665 m/s².

These forces act on the suspended pulley assemblies. They are not automatically the tension in one chain strand. For an ideal movable pulley supported by two vertical strands, each strand carries half the supported weight. If the two equal-tension strands are inclined by α from vertical, their tension is W/(2 cos α).

The drive wheel responds to the difference between its chain-side tensions, multiplied by its effective radius. Pulley geometry and radius are therefore needed for torque. This two-mass calculator does not claim to calculate that torque.

Default 5 kg and 150 g weights

A 5 kg main weight and 150 g tension weight give a mass ratio of about 33.3:1 and a counterweight share of 3%. Their gravitational forces are approximately 49.03 N and 1.47 N.

Those numbers are weight comparisons, not an approved setting for a particular clock. In the special ideal case of vertical support strands, their respective strand tensions would be approximately 24.52 N and 0.735 N. The expanded diagram has inclined strands, so that vertical-strand example is not presented as its measured tension.

Maintaining power is not a clock-rate prediction

The chain geometry is constrained, but the speed of the demonstration is prescribed. The model excludes chain mass, bearing friction, click impact, winding acceleration, gear-train losses and escapement demand.

The two entered masses do not determine suitable counterweight settings, pendulum amplitude, chain tolerances or winding time. Weight shapes are illustrative and are not a density or dimensional model.

Maintaining-power questions

Does the small counterweight power the clock during winding?

It tensions the return loop. The main weight remains connected to the drive wheel while being raised.

Why does the lower pulley move with its weight?

The weight is suspended from that pulley’s axle. Moving the chain at the winding wheel changes its height.

Why does the animation run quickly?

The sequence is accelerated to show the transfer of chain during running and winding. It is not real elapsed clock time.

Can the displayed mass percentage certify a suitable counterweight?

No. A specific clock needs its chain routing, pulley dimensions and operating demand checked.

References

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: