Belt-driven Elevator Mechanism: How MRL Traction, Polyurethane Belts & Sheave Geometry Work

← Back to Engineering Library

A coated-belt traction elevator uses a powered sheave to move a car and counterweight. Explore a generic two-to-one suspension arrangement and compare the bending geometry of a flat belt around a sheave.

Traction drive and separate positioning equipment

The car in this model is driven by a rotary traction sheave. Selecting its drive, suspension belts, brakes and protective equipment requires the elevator system’s specified components and operating data.

For a separate powered positioning task, the linear actuator wiring diagram generator helps plan actuator controls and the FIRGELLI linear actuator range provides force and stroke options. The linear actuator replacement finder compares an existing actuator with available models. These tools do not specify passenger-elevator suspension or protective equipment.

Belt-driven Elevator Interactive Calculator

Change sheave diameter, belt thickness and the comparison values. The bend detail and diameter comparison respond to the inputs; the car motion illustrates a generic 2:1 suspension.

0°

Bend Ratio
--
Diameter at reference
--
Diameter difference
--
Difference from reference
--

Equation Used

R = (D + t) / t; D_reference = (R_reference − 1)t; difference = 100(R/R_reference − 1)
The mid-thickness diameter D + t is a geometric reference. A composite belt’s cord bending and fatigue performance depend on its construction and approved sheave specification. The selected ratio is not a universal minimum or a safety margin.
  • D is the sheave contact diameter; t is total belt thickness.
  • The belt mid-thickness line is used only for geometric comparison.
  • The reference ratio and comparison diameter are user-selected benchmarks.
  • No traction, tension, fatigue, passenger capacity or compliance calculation.

Otis Gen2 Life technical specifications document coated steel belts and a 2:1 configuration. The animation is a generic suspension illustration, not that product’s installation layout.

Same mechanism and inputs as the interactive calculator.

How the suspension works

The illustration follows one continuous belt from a fixed overhead anchor, under a sheave carried by the car, over a fixed powered traction sheave, under a sheave carried by the counterweight, and up to a second fixed anchor. The car and counterweight each have two supporting belt legs.

When the car rises, its two vertical legs shorten. The counterweight moves down by the same distance, lengthening its two legs. With an inextensible belt, the total path length stays constant. At the drive sheave, belt travel is twice car travel. The moving marks trace the belt material, with both anchored ends held fixed.

A complete elevator also has guide systems, controls, brakes and independent protective equipment. Those systems are outside this illustration. Multiple parallel belts and product-specific routing are not represented.

Where coated-belt traction is used

Coated steel belts are used in commercial traction elevators, including machine-room-less systems. Otis lists flat coated steel belts, a gearless permanent-magnet machine and a 2:1 configuration for its Gen2 Life product. The layout shown here explains the suspension principle without reproducing a particular installation.

What the calculator measures

For contact diameter D and belt thickness t, the diameter at the belt mid-thickness line is D + t. The geometric bend ratio is R = (D + t)/t. Rearranging gives the contact diameter corresponding to a selected reference ratio: D_reference = (R_reference − 1)t.

The ratio difference is 100(R/R_reference − 1) percent. The diameter comparison is 100(1 − D/D_comparison) percent. Neither result is a strength margin or an energy-saving prediction.

The difference between car and counterweight loads is not the tension carried by each supporting belt leg. This calculator evaluates bending geometry; load distribution and traction require a separate analysis.

Worked geometry comparison

With an 88 mm contact diameter and a 3 mm belt, R = (88 + 3)/3 = 30.33. A selected reference ratio of 30 corresponds to an 87 mm contact diameter. The ratio is 1.11 percent above that reference. Against a 600 mm comparison diameter, 88 mm is 85.33 percent smaller. These are geometric comparisons, not approval to use that belt and sheave combination.

Reading the results

A smaller sheave makes the drive more compact, but a diameter ratio alone cannot establish belt life or traction. Cord diameter, construction, bending cycles, load and the approved belt/sheave combination matter. The side-by-side diameter view makes the dimensional difference visible without implying interchangeable capacity.

Calculator questions

Does a positive ratio difference mean the belt is suitable?

No. It means only that the entered geometry exceeds your selected reference ratio. Use the belt and elevator manufacturer’s specified combination.

Why do both the car and counterweight have a moving sheave?

They each use two supporting legs in this generic 2:1 arrangement. This makes drive-belt speed twice the car speed.

Why does the car travel stay the same when I change the diameter?

The overview demonstrates the suspension at a schematic size. The dimensioned detail and comparison views show your entered sizes; no hoistway travel or operating speed is entered.

Primary reference

Otis Gen2 Life brochure, technical specifications: coated steel belts, gearless machine and 2:1 configuration. This supports the suspension type, not a universal sheave-to-thickness ratio.

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: