Accelerated Circular Motion Explained: How It Works, Formula, Diagram, and Mechanism Uses

← Back to Engineering Library

A rotor accelerating about a fixed shaft changes its angular speed over time. Its rim has a tangential acceleration set by angular acceleration and radius. Enter those two quantities below to compare rim acceleration and speed ramp, and watch a repeated spin-up from rest.

Accelerated Circular Motion Interactive Calculator

Vary angular acceleration and rotor diameter to see rim acceleration, equivalent g load, and spin-up rate.

0°

Rim Accel
--
Equivalent Load
--
Radius
--
Speed Ramp
--

Equation Used

a_t = alpha * r, where r = diameter / 2

The rim acceleration is tangential: a_t = αr. The Equivalent Load card expresses this acceleration in multiples of g; it is not a force, bearing load or material stress. The speed-ramp card converts α to rpm/s. Torque and inertia are not calculator inputs.

  • Rigid circular rotor
  • Constant angular acceleration
  • Diameter is the outside rotating diameter
  • Friction and bearing losses are not included
Same mechanism and inputs as the interactive calculator.

Angular and rim acceleration

Every point on a rigid rotor has the same angular acceleration about its fixed shaft. A point farther from the axis has a greater tangential acceleration: at = αr. This component changes the magnitude of its velocity.

A rotating point also has centripetal acceleration ac = ω²r toward the axis. The tangential and radial components are perpendicular. A constant-speed rotor has zero tangential acceleration but still has centripetal acceleration.

The animation repeats a two-revolution spin-up from rest. The arrow shows the tangential component. Playback is slowed so the motion can be followed; the displayed time and speed use the chosen angular acceleration.

What determines a real spin-up?

  • Net torque: motor or other drive torque after accounting for resisting torques.
  • Moment of inertia: mass distribution about the shaft, including attached loads and drive components.
  • Motion command: the desired speed and acceleration through time.
  • Mechanical support: bearings, shaft, coupling and attachments that carry the loads.

The animation treats the rotor as rigid. Flexible shafts, control response and torque that varies with speed can change actual motion.

Using the calculation

Start-up, braking and indexing all involve changing angular speed. For a rotary table, an acceleration profile sets how quickly a station moves into position. For a spindle, the speed ramp describes how quickly it reaches the commanded speed.

This tool compares motion at the rim; it does not select a motor or approve a rotor speed. Motor selection also requires torque versus speed, total inertia, duty cycle, braking energy and the drive’s electrical limits. A mass alone is insufficient to determine inertia: the distance of that mass from the axis matters.

Equations for fixed-axis rotation

For outside diameter D in millimeters, radius r = D/2000 in meters. Tangential rim acceleration is at = αr in m/s², and its equivalent g value is at/9.81. The speed ramp is α×60/(2π) in rpm/s.

At constant α, angular speed is ω = ω₀+αt and angular displacement is θ−θ₀ = ω₀t+αt²/2. Angles in these equations are in radians. For a rigid body with constant inertia about a fixed axis, net torque is τnet = Iα, using N·m, kg·m² and rad/s².

Motor torque must also account for resisting torque. During positive rotation with a positive resisting-torque magnitude τr, τmotor = Iα+τr. During deceleration α is negative, so the motor may supply braking torque. Work and energy balance must include any energy returned to the drive.

The centripetal component ω²r is distinct from the tangential value shown on the output card. Neither component by itself gives material stress or the net bearing load of a balanced rotor.

Worked examples

Rim acceleration

For a 200 mm rotor accelerating at 500 rad/s², r = 0.100 m and at = 50 m/s², or about 5.10 g. The speed ramp is approximately 4,774.65 rpm/s. These are motion values, not structural or attachment ratings.

An illustrative rotary-table move

Consider an ideal uniform 12 kg disk of radius 0.300 m. Its inertia is I = mr²/2 = 0.54 kg·m². To move 45° = π/4 radians in 0.4 s from rest to rest, assume constant acceleration for half the time and equal-magnitude deceleration for the other half, with no cruise.

For this triangular speed profile, α = 4θ/t² = 19.635 rad/s² and peak speed is αt/2 = 3.927 rad/s. Inertial torque magnitude is 0.54×19.635 = 10.603 N·m. With an illustrative 0.8 N·m resisting torque, motor torque during acceleration is 11.403 N·m and during deceleration is −9.803 N·m while the disk still turns forward.

Keeping the same angle, a 0.6 s move requires α ≈ 8.727 rad/s² and acceleration-phase motor torque ≈ 5.512 N·m. A 0.25 s move requires α ≈ 50.265 rad/s² and approximately 27.943 N·m. Actual fixture inertia and process forces must be added. Eight point-like 0.5 kg fixtures at radius 0.25 m add 8×0.5×0.25² = 0.25 kg·m² in total, not per fixture.

The disk assumptions and torque calculations extend beyond the calculator’s two inputs. They are a worked model, not a specification for a named packaging machine or a motor recommendation. The ideal abrupt changes in acceleration may also require a smoother command in a flexible drive.

Choosing a drive arrangement

Arrangement What to compare
Servo system Feedback resolution, available torque throughout the move, control response and thermal duty.
Stepper system Torque-speed curve, acceleration profile, resonance and whether position feedback is required.
Variable-frequency motor drive Motor and drive speed range, control mode, available starting torque and braking provisions.
Gear reduction Motor speed, reflected inertia, efficiency, backlash and gearbox load ratings.

These arrangements do not have universal acceleration, accuracy, price or life figures. Use the actual motor, drive and transmission data at the required operating conditions.

Accelerated-rotation questions

Available motor torque and resisting torque may change with speed, and inertia or current limits may differ from the assumed values. Constant-acceleration timing only applies when the required net torque is available throughout the ramp.

For an ideal reduction ratio N = motor speed/load speed, the load inertia reflected to the motor is I_load/N². Include motor and transmission inertia, losses and the higher motor speed as well. No single inertia ratio makes gearing automatically preferable.

No. Overshoot depends on the command profile, control system, compliance, backlash and damping. A rigid-body torque calculation establishes a motion requirement but does not replace a dynamic model or drive tuning.

It depends on load inertia, process torque and the gearhead’s permitted repeated, emergency and continuous loads. Check the complete duty against the manufacturer’s definitions; there is no universal acceleration threshold or multiplier of continuous torque.

Include each rotating part about the appropriate axis. Use its mass distribution, not only total mass. A point-like mass contributes mr², while a uniform disk contributes mr²/2 about its central axis. Transfer quantities through gears consistently.

An eccentric mass produces a rotating force of magnitude mω²e, where e is its offset. For 2 kg at 5 mm offset and 3000 rpm, the magnitude is about 987 N. Support reactions depend on shaft and bearing geometry; this is different from the internal centripetal loading of an ideally balanced rotor.

References and further reading

OpenStax: Angular Acceleration explains angular and tangential quantities. Newton’s Second Law for Rotation covers net torque and inertia about a fixed axis.

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: