Hopper and Bell: Furnace Charging and Event-Count Example | FIRGELLI

← Back to Engineering Library

A hopper and bell can charge a furnace in batches: the hopper holds material above a movable bell, and lowering the bell releases the charge. Hiscox illustrates this furnace arrangement in entry 1424. The calculator below is a separate event-count exercise; its tap-driven cone illustration does not reproduce the historical furnace mechanism.

Mass per Tap: Event-Count Calculator

Multiply rotational speed, entered taps per revolution and entered mass per tap to obtain an average mass-rate scenario.

0°

Entered-mass Rate
--
Tap Frequency
--
Entered-mass Rate
--
100 kg/h Index
--

Equation Used

tap frequency=n RPM/60; mass rate=tap frequency times entered mass/tap; 100 kg/h index=100 times rate/100 kg/h
Rotation rate sets the frequency of the entered tap events in this separate arithmetic example. It does not describe the historical furnace bell’s movement.
  • Constant entered taps per revolution and mass per tap.
  • Every counted event releases the entered mass with no missed or extra flow.
  • No granular-flow, arching, segregation, moisture, throat, bell dynamics or mill-load model.
  • The 100 kg/h baseline is a fixed comparison, not a rating or target.

Mass per tap must be measured or assumed by the user; the calculator does not derive it from bell, throat, grain or hopper geometry. The final percentage is only comparison with a fixed 100 kg/h baseline.

Same mechanism and inputs as the interactive calculator.

Holding and releasing a charge

In Hiscox’s hopper-and-bell arrangement, coal or ore is placed in the hopper while the bell supports the charge. Lowering the bell opens a discharge path into the furnace. This is a batch-release action.

The calculator instead multiplies an entered number of taps per revolution by an entered mass per tap. Its suspended-cone illustration is qualitative: it does not calculate bell travel, contact, granular discharge or furnace charging.

Use with measured event mass

The conversion can scale a measured average mass per event across rotation rates. It cannot set hopper dimensions, predict bridging or approve mill operation.

Frequency and unit conversion

Tap frequency is nN/60 in events per second. Multiplying by entered kilograms per event gives kg/s, then multiplying by 3,600 gives kg/h. The imperial value is the same rate converted to lb/min.

Worked example

At 90 rpm and four entered taps per revolution, frequency is 6 Hz. If measured mass averages 4.2 g per tap, the arithmetic rate is 90.72 kg/h, or about 3.33 lb/min.

Scope and limitations

Real feed depends on material size, shape, density, moisture and friction; fill head, wall angles, outlet and bell geometry; vibration and tap impulse; segregation, ratholing and arching; and downstream load. Measure actual mass flow across the intended operating range.

Frequently asked questions

What did Hiscox’s hopper and bell do?

It held a charge of coal or ore above a furnace and released it when the bell was lowered.

Does this calculator model that furnace mechanism?

No. It converts an entered rotation rate, taps per revolution and mass per tap into an average mass rate. Its qualitative cone illustration is a separate example.

Does the calculator predict grams per tap?

No. Measure the average released mass or enter an assumed value. Flow consistency and missed events are not modeled.

Is the 100 kg/h index a capacity rating?

No. It only compares the calculated rate with a fixed 100 kg/h baseline.

Does the illustration prove that a hopper will not bridge?

No. It contains no granular-flow or arching model.

Historical source and calculation basis

Gardner D. Hiscox, Mechanical Movements, Powers, Devices and Appliances, entry 1424, describes a hopper and lowering bell for charging a furnace with coal or ore. The event-frequency exercise on this page is not a performance model of that apparatus.

The numerical results use event counting and mass-unit conversion. Mass per tap is an input, not a quantity calculated from material or hopper geometry.

Building or designing a mechanism like this?

Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.

← Back to Mechanisms Index
Share This Article
Tags: