A travelling pinion rolls between a fixed lower rack and a guided upper rack. Moving the pinion spindle through one unit of distance moves the upper rack through two. This stroke gain trades force for distance: the ideal output force is half the force applied to the carrier.
Doubling Stroke Length via Rack and Pinion Interactive Calculator
Move the pinion carrier between a grounded rack and a guided output rack. Compare twice the stroke and speed with half the ideal force, and inspect both tooth contacts in the moving close-up.
Equation Used
- The lower rack is fixed and both rack pitch lines remain tangent to the pinion pitch circle.
- Both racks share the pinion module and tooth pitch.
- No backlash, friction or elastic deformation.
- Force transmission is ideal and quasi-static.
- Playback uses illustrative smooth reversals; no acceleration is specified.
Ideal rigid rolling gears; no friction, acceleration or load rating. Rack lengths and bearings are illustrative.
A rolling gear doubles the upper contact motion
The lower rack is attached to the frame. A separate slide carries the pinion spindle. As the slide advances, the pinion rotates because its lower teeth mesh with the grounded rack. The upper rack meshes with the opposite side of the same gear and runs in its own guide.
The lower pitch contact has zero velocity relative to the frame. Rotation therefore contributes a tangential velocity equal to the carrier speed. At the upper contact, that contribution adds to the carrier translation, producing twice the input speed.
The illustration follows Brown’s movement 118. Bearing blocks and rails make the grounded and travelling members clear. The magnified mesh view follows the pinion; in that view the lower rack appears to move backward, although it remains stationary relative to the main frame.
Explore a compact travel multiplier
The arrangement is useful when an input slide must produce a longer output stroke. The calculator separates carrier stroke, applied force, pitch diameter and travel speed. Changing the pitch diameter changes pinion rotation, tooth count and drawn size; it does not change the ideal two-to-one travel ratio.
The model shows a 3 mm module pinion with an even number of teeth. The pitch-diameter slider therefore advances in 6 mm steps. Both racks use the same pitch and 20° working flanks. Tooth roots, supporting hardware and end allowances are illustrative.
Travel, rotation and ideal work
For carrier displacement x and pinion pitch radius R, the rolling condition on the fixed rack gives rotation θ=x/R. The upper rack displacement is x+Rθ=2x. Thus output stroke is 2S and output speed is 2v.
With ideal steady force transmission, input work Fin dx equals output work Fout d(2x), giving Fout=Fin/2. Equivalently, the two rack contact forces balance the pinion torque and together react the carrier force.
Pinion revolutions per one-way stroke are S/(Ï€D). Transmitted power is Fin v/1000 watts when force is in newtons and speed in mm/s. The output product Fout vout gives the same value. These relationships exclude friction and acceleration loads.
A 100 mm carrier stroke produces 200 mm output
At the starting inputs, a 100 mm carrier stroke drives the upper rack through 200 mm. A 1000 N carrier force provides 500 N ideal output force. At 50 mm/s carrier speed the rack travels at 100 mm/s and ideal transmitted power is 50 W.
The 72 mm pitch-diameter pinion has 24 teeth at 3 mm module. It rotates about 0.442 revolution during that one-way stroke. A larger pinion rotates less for the same travel while preserving the two-to-one displacement ratio.
Zero travel speed stops automatic playback and sets speed and power results to zero. The position slider still permits manual inspection. Force remains an ideal static transmission relationship rather than a claim that the stationary mechanism consumes power.
What this model establishes
The calculator establishes ideal displacement, speed and force ratios. It does not determine gear strength, allowable load, backlash, guide stiffness, lubrication, bearing life or a permissible operating speed. Those require the actual components, loads and duty cycle.
Doubling output travel also doubles output speed for a given carrier speed. The input must provide twice the desired ideal output force. Neither the rack arrangement nor the extra mesh justifies a universal contact-stress multiplier.
The drawing adds rack length and guide travel to keep both meshes engaged. It is a kinematic explanation, not a manufacturing drawing. Smooth playback reversals are illustrative; the entered speed is a steady travel-speed comparison.
Stroke-doubler questions
Does pinion diameter change the stroke ratio?
No. The same pinion contacts both racks, so its radius cancels from the two-to-one travel relationship. Diameter changes its required rotation.
Does the actuator need more force or more speed?
For a specified output, the ideal input requires twice the output force and half the output speed.
Why does the lower rack move in the close-up?
The close-up moves with the pinion carrier. The main view shows that rack fixed to the frame.
Does a larger force setting prove the teeth can carry it?
No. It changes the ideal transmitted force calculation; tooth and bearing capacity are outside this model.
Can I inspect a stopped mechanism?
Yes. Set speed to zero or pause, then use the cycle-position control.
References
Henry T. Brown, Five Hundred and Seven Mechanical Movements, movement 118, describes a travelling pinion between a fixed rack and a second guided rack. The two-to-one travel relationship follows from its two pitch contacts; the ideal force relationship follows from conservation of work.
Building or designing a mechanism like this?
Explore the precision-engineered motion control hardware used by mechanical engineers, makers, and product designers.