Spring Hammer

Robbie Dickson
2026-04-26T03:53:27-07:00

Spring Hammer mechanism explained — how the leaf-spring drive multiplies blow energy in forging shops, with formulas, real tonnage examples and shop tradeoffs.
More

A Spring Hammer is a mechanically driven forging hammer that uses a flexing leaf or coil spring between the crank arm and the ram to store and release impact energy on hot metal. Charles A. Beaudry patented the toggle-and-leaf-spring layout in 1888, and Bradley followed with the strap and helve variants. The spring decouples the ram from the crank so the tup can accelerate downward faster than the crank pin moves, multiplying blow energy. Modern shop hammers in the 25–500 lb ram class deliver 200–300 blows per minute on bar stock up to roughly 4 inch square.

How It Works Where It’s Used Formula Animated Calculator Worked Example Comparison FAQ

Spring Hammer Interactive Calculator

Vary ram weight, stroke, blow rate, and spring amplification to see tup speed, blow energy, gain, and delivered power.

Ram Weight (W)

Stroke (S)

Blow Rate (BPM)

Spring Amp (ks)

Tup Speed

--

Blow Energy

--

Energy Gain

--

Blow Power

--

Equation Used

E_blow = 0.5*(W_ram/g)*v_tup^2; v_tup = ks*pi*S*(BPM/60)

Blow energy is the kinetic energy of the tup at impact. The spring amplification factor ks increases the estimated terminal velocity, so energy changes with the square of ks, stroke, and BPM.

Imperial calculation with ram weight in lbf converted to slugs using g = 32.174 ft/s^2.

Stroke is total ram travel and is converted from inches to feet.

ks is a constant terminal-velocity amplification factor for the spring action.

Losses, die rebound, clutch slip, and spring fatigue effects are neglected.

FIRGELLI Automations - Interactive Mechanism Calculators

Watch the Spring Hammer in motion

Video: Spring hammer by Nguyen Duc Thang (thang010146) on YouTube. Used here to complement the diagram below.

Spring Hammer Mechanism Diagram.

The Spring Hammer in Action

The core idea is energy storage. A continuously rotating crank — driven by a flat belt off a lineshaft or, today, a 3 to 7.5 HP motor — pulls one end of a stiff leaf spring up and down. The other end of the spring is pinned to the ram, also called the tup. Because the spring flexes, the ram does not slavishly follow the crank's sinusoidal motion. It lags on the upstroke, stores elastic energy, then snaps downward when the spring unloads. That snap is what gives the Spring Hammer its characteristic sharp, fast blow — far harder than a crank-only hammer of the same stroke could deliver.

Geometry matters. On a 50 lb Little Giant, the spring is typically a 5-leaf pack about 7/16 inch thick per leaf, clamped at the toggle. If you over-stiffen the spring — say by adding a sixth leaf — the ram tracks the crank too closely and you lose the snap. Too soft and the ram floats, you get weak blows and the linkage slaps. Toggle pin clearance must stay under about 0.010 inch; once the bushings wear past 0.020 inch you'll hear the hammer clatter at the top of the stroke and the blow energy drops noticeably. Stroke length on most shop hammers sits between 6 and 10 inches, and the sweet spot for blow rate is 200 to 300 BPM.

Failure modes are predictable. Broken leaf springs are the number one issue, almost always from running the hammer cold or hitting the dies together with no stock between them — that puts a shock load through the spring it was never sized for. Worn toggle bushings come second. Cracked rams and bent pitman arms come from operators leaving cold stock under the dies and stalling the crank near bottom dead centre.

Key Components

Leaf Spring (or Coil Spring) Pack: Stores and releases the energy that drives the ram. On a 50 lb Beaudry-pattern hammer the pack is typically 5 leaves of 1095 spring steel, hardened to 45–50 HRC. Spring rate sits around 800–1200 lb/in — soft enough to flex meaningfully on each stroke, stiff enough to throw the ram hard.

Toggle Links: Connect the crank pin to the spring and convert rotary crank motion into vertical spring deflection. Toggle pins run in bronze bushings with 0.005–0.010 inch clearance. Once clearance exceeds 0.020 inch the linkage slaps audibly and blow energy falls off.

Ram (Tup): The moving mass that delivers the blow. Cast iron or forged steel, typically 25 to 500 lb on shop-class hammers. Ram weight is the dominant factor in blow energy along with terminal velocity.

Crank and Pitman: Driven by the motor or lineshaft pulley through a clutch. Crank radius sets the nominal stroke — 3 inch crank radius gives 6 inch stroke. Pitman is the connecting arm between crank pin and toggle assembly.

Anvil Cap and Sow Block: The lower die holder mounted on the anvil. The anvil itself should weigh 10× to 15× the ram weight to absorb the blow without rebounding. A 50 lb hammer wants a 500–750 lb anvil; less than that and the bottom die bounces and your forging splits.

Clutch (Toggle or Friction): Engages the crank to the constantly-spinning belt pulley. Most shop hammers use a foot-treadle linkage so the smith can modulate blow strength by controlling clutch slip.

Who Uses the Spring Hammer

Spring Hammers earn their keep wherever a small shop needs to move metal fast without the capital cost of a self-contained air hammer. They sit at the heart of toolmaking shops, knifemaking forges, ornamental ironwork shops, and farrier supply outfits. The mechanism's strength is repetitive, controllable medium-energy blows on bar stock in the 1/2 inch to 4 inch range. Where it loses ground is on heavy industrial forging — above about 500 lb ram weight, air and steam hammers take over because spring fatigue life becomes the limiting factor.

Custom Knifemaking: A bladesmith in Bozeman Montana uses a 50 lb Little Giant Spring Hammer to draw out 1084 carbon steel billets from 1 inch round into 1/4 inch thick blade stock at 240 BPM.

Architectural Ironwork: A wrought iron shop in Charleston runs a 100 lb Beaudry Spring Hammer to texture 3/4 inch square bar for gate pickets, finishing 60 pickets per hour.

Farrier Supply: A horseshoe manufacturer in Lexington Kentucky uses a 25 lb Bradley strap hammer to swage front-pattern shoes from 5/16 × 3/4 inch flat bar.

Hand Tool Manufacturing: A Japanese tool shop forging adze heads runs a 75 lb spring hammer pattern to draw out the 1075 steel cutting edge before heat treat.

Toolmaking and Die Sink Work: A blanking-die shop in Sheffield uses a 150 lb Beaudry Spring Hammer to forge near-net 4140 die blocks before final machining, saving 30% on stock removal.

Restoration Blacksmithing: A heritage smithy at Colonial Williamsburg keeps a 1908 Fairbanks 50 lb Spring Hammer in production for reproducing 18th-century strap hinges and door hardware.

The Formula Behind the Spring Hammer

The figure that matters to a smith is blow energy — how hard the tup hits the workpiece, measured in foot-pounds. Blow energy scales with ram mass and the square of terminal velocity, so a small change in stroke length or BPM produces a large change in how the hammer feels. At the low end of the typical operating range, around 150 BPM with a short stroke, the hammer taps lightly and is good for finishing work. At the nominal sweet spot of roughly 240 BPM and full stroke, you get the hard, controllable forging blow the mechanism was designed for. Push past 300 BPM and spring fatigue accelerates while terminal velocity stops climbing — the spring runs out of time to fully unload between strokes.

Eblow = ½ × mram × vtup², where vtup ≈ ks × π × S × (BPM / 60)

Variables

Symbol | Meaning | Unit (SI) | Unit (Imperial)
Eblow | Energy delivered per blow | J (joules) | ft·lb
mram | Ram or tup mass | kg | lb
vtup | Tup terminal velocity at impact | m/s | ft/s
S | Stroke length (top of ram travel to bottom) | m | in or ft
BPM | Blows per minute (crank speed) | 1/min | 1/min
ks | Spring amplification factor (typically 1.4–1.8 on a properly tuned leaf spring; 1.0 on a pure crank hammer) | dimensionless | dimensionless

Worked Example: Spring Hammer in a 50 lb Little Giant in a knife shop

A custom knife shop in Boise Idaho is setting up a restored 50 lb Little Giant Spring Hammer to draw out 1084 carbon steel blade billets. The hammer has an 8 inch stroke, runs through a 7 inch crank pulley off a 3 HP motor, and the leaf spring is freshly re-arched giving a measured amplification factor ks of about 1.6. The smith wants to know the blow energy at 150 BPM (warmup tapping), at 240 BPM (working), and at 300 BPM (top end before spring fatigue rises sharply).

Given

mram = 50 lb (22.7 kg)

S = 8 in (0.203 m)

ks = 1.6 dimensionless

BPMnom = 240 1/min

Solution

Step 1 — convert nominal BPM to revs per second and find tup velocity at 240 BPM:

vtup,nom = 1.6 × π × 0.203 × (240 / 60) = 1.6 × π × 0.203 × 4.0 ≈ 4.08 m/s

Step 2 — compute blow energy at the nominal working speed using ½ × m × v²:

Eblow,nom = ½ × 22.7 × (4.08)² ≈ 189 J ≈ 139 ft·lb

Step 3 — at the low end of the working range, 150 BPM (warmup or finishing taps):

vtup,low = 1.6 × π × 0.203 × (150 / 60) ≈ 2.55 m/s, Eblow,low ≈ ½ × 22.7 × 2.55² ≈ 74 J ≈ 54 ft·lb

54 ft·lb is a polite tap — enough to scale-flake a hot billet and dress edges, but you will not draw out 1 inch round stock at this speed. The hammer feels under-worked and the smith hears a soft thud rather than the sharp bark of a hammer in its sweet spot.

Step 4 — at the high end, 300 BPM, theoretical numbers keep climbing but reality intervenes:

vtup,high = 1.6 × π × 0.203 × (300 / 60) ≈ 5.10 m/s, Eblow,high ≈ ½ × 22.7 × 5.10² ≈ 295 J ≈ 218 ft·lb

That 218 ft·lb figure is theoretical. In practice above 280–300 BPM the leaf spring no longer has time to fully unload between strokes, so ks falls from 1.6 toward 1.3 and real blow energy plateaus near 170 ft·lb. Spring fatigue life also drops sharply — leaves that survive 2 million cycles at 240 BPM may crack at 600,000 cycles at 300 BPM.

Result

Nominal blow energy at 240 BPM works out to about 139 ft·lb (189 J), which is the textbook working figure for a 50 lb Little Giant on 1 inch round 1084. At that energy the smith can draw 1 inch round down to 3/8 inch flat in 4–5 heats, with the tup making a clean sharp bark on each blow. Comparing the range: 54 ft·lb at 150 BPM feels like polite finishing taps, 139 ft·lb at 240 BPM is the design sweet spot, and the theoretical 218 ft·lb at 300 BPM never materialises because the spring runs out of unload time. If your hammer measures noticeably below 139 ft·lb at 240 BPM, check three things in order: (1) leaf spring arch — a sagged or mismatched spring pack drops ks from 1.6 to under 1.2, (2) anvil-to-ram weight ratio — anything below 10:1 and the anvil rebounds rather than absorbing, swallowing energy from the workpiece, (3) loose anvil cap dovetail wedges — even 1/16 inch of looseness in the lower die seat costs you 15–20% of effective blow energy because the die bounces.

Choosing the Spring Hammer: Pros and Cons

Spring Hammers compete primarily with self-contained air hammers (think Anyang, Sahinler) and with mechanical helve hammers. Each fits a different shop size, budget, and forging profile. The honest comparison is on cost, blow control, ram weight scalability, and maintenance burden — not on which is universally better.

Property | Spring Hammer (Beaudry/Little Giant) | Self-Contained Air Hammer | Helve Hammer
Typical ram weight range | 25–500 lb | 55–1100 lb | 10–200 lb
Blows per minute (working) | 200–300 BPM | 120–250 BPM | 80–150 BPM
Blow energy at 50 lb ram class | ≈ 140 ft·lb | ≈ 180 ft·lb | ≈ 80 ft·lb
Blow control / modulation | Fair — clutch slip controls intensity | Excellent — treadle controls air pressure stroke by stroke | Poor — largely fixed once running
Capital cost (used, working condition) | $3,500–8,000 | $8,000–25,000 | $1,500–4,000
Primary failure mode | Broken leaf spring (1–3 year life under heavy use) | Worn ram seals, cracked cylinder | Worn helve pivot bushings
Maintenance interval | Re-grease toggle pins every 40 hours; spring inspection monthly | Seal replacement every 2,000 hours | Bushing re-grease every 20 hours
Best application fit | Knife shops, ornamental iron, small toolmaking | Production forging, larger die work | Restoration shops, small bladesmiths

Frequently Asked Questions About Spring Hammer
Why does my Little Giant feel like it lost half its punch after I replaced the leaf spring with a thicker pack?

You stiffened the spring past the point where it can flex meaningfully on each stroke. The whole point of the Spring Hammer is that the spring stores energy on the upstroke and snaps the ram down faster than the crank moves. A too-stiff pack makes the ram track the crank closely, dropping your amplification factor ks from around 1.6 toward 1.0 — which roughly halves blow energy because energy scales with velocity squared.

Pull a leaf out and try it again. On a 50 lb hammer the original 5-leaf pack at about 7/16 inch per leaf is calibrated to the ram weight and stroke. Adding mass to the spring without re-tuning the toggle geometry never works.

How do I size the anvil mass for a Spring Hammer if I'm pouring a new concrete pad and base?

Rule of thumb: anvil mass should be 10× to 15× ram mass. A 50 lb ram wants a 500–750 lb anvil block. Below 10:1 and you waste a measurable fraction of every blow into anvil rebound rather than into the workpiece — the steel under the dies springs back instead of moving.

For the foundation under the anvil, figure another 10× the anvil mass in concrete and isolate it from the shop slab with a layer of hardwood or oak timbers. A 50 lb hammer on a shared slab will crack the slab inside a year and the neighbours will hear about it long before that.

Should I run a Spring Hammer at maximum BPM to get maximum production rate?

No — and the math explains why. Above roughly 280 BPM the leaf spring runs out of time to fully unload between strokes, so amplification factor ks drops from 1.6 toward 1.3. Theoretical blow energy keeps rising on paper but real blow energy plateaus or falls. At the same time spring fatigue life collapses — leaves that survive 2 million cycles at 240 BPM may crack at 600,000 cycles at 300 BPM.

The production-optimum BPM for most 50–100 lb shop hammers sits at 220–260. You move more metal per hour at 240 BPM than at 300 BPM because each blow does meaningfully more work and you spend less time replacing springs.

Which makes more sense for a one-smith knife shop — a 50 lb Spring Hammer or a 55 lb self-contained air hammer?

If budget is the constraint and you do mostly bladesmithing on stock under 1.5 inch, the Spring Hammer wins. A used 50 lb Little Giant in working order runs $3,500–6,000. A new Anyang 55 lb air hammer is $9,000–12,000 plus a 5 HP single-phase or 3-phase service.

If blow control matters more than purchase price — for instance if you forge damascus billets or do delicate finishing on tapered tangs — the air hammer is worth the premium. Air hammers modulate from a soft tap to full energy on a single treadle. A Spring Hammer modulates through clutch slip, which is coarser and harder on the clutch leather.

Why does my hammer leave a rectangular witness mark on the workpiece offset toward one side of the die instead of centred?

Your ram is not falling square to the anvil. Three causes in order of likelihood: (1) the ram guide gibs are worn — on a 50 lb Little Giant once total ram side play exceeds about 0.030 inch the ram cocks under load and the dies kiss off-square. (2) The anvil cap dovetail wedges are loose, letting the lower die rotate a few thousandths under each blow. (3) The pitman arm or toggle is bent, usually from someone hitting the dies together cold at some point.

Diagnostic check: chalk the lower die face, take one slow blow on a piece of soft aluminium, and look at the print. If the print is heavier on one edge by more than about 0.010 inch difference in depth, pull the gibs and measure them.

Can I drive a Spring Hammer with a VFD and a 3-phase motor to get variable BPM?

Yes, and it's one of the better upgrades you can do — but with a caveat. A VFD lets you tune BPM to the work, which is genuinely useful (slow for finishing, fast for drawing out). The catch is that the leaf spring's resonant behaviour is tuned to a narrow BPM band. Run too far below the design BPM and the ram becomes lazy because the spring doesn't fully load. Run too far above and you hit the unload-time limit described earlier.

Practical range on a typical 50 lb hammer originally rated 240 BPM: usable VFD range is roughly 150 to 280 BPM. Outside that band you're fighting the spring physics rather than using them.

My toggle pins keep wallowing out their bushings every few months — what's the underlying cause?

Almost always one of two things. First, you're hitting cold or near-cold stock. A blow that should travel through hot 2,100°F steel and dissipate in plastic deformation instead bounces back through the linkage when the steel is below about 1,500°F. That shock load goes straight into the toggle pins and bronze bushings.

Second, the grease schedule. Toggle pins on a Beaudry-pattern hammer want grease every 40 working hours minimum. A dry pin running at 240 BPM sees 14,400 cycles per hour — bushings dry out fast. Switch to a tacky open-gear grease and re-grease at every shift change. If pins still wallow after fixing both issues, check that the pitman arm is actually straight; a 0.020 inch bend induces a side load on the pin that no grease will cure.

References & Further Reading

Wikipedia contributors. Power hammer. Wikipedia

Related Mechanisms

Other mechanisms in the FIRGELLI library that share principles, geometry, or applications with this one.

Helve Trip Hammer Mill & Factory Appliances

Friction Drop Hammer Mill & Factory Appliances

Revolving Rapid-blow Hammer Mill & Factory Appliances

Blacksmith's Helper Mill & Factory Appliances

Power Stamping Press Mill & Factory Appliances

Spring Friction Clutch Mill & Factory Appliances

Atmospheric Hammer Pneumatic & Air Power

Vertical Drop Hammer Gears & Gearing

Oldham Coupling Couplings & Joints

Compressed Air Hammer Pneumatic & Air Power

Related Calculators

Interactive calculators from the FIRGELLI engineering library that apply to this mechanism.

Leaf Spring Calculator — Deflection and Stress Engineering Calculator

Spring Energy Storage Calculator Engineering Calculator

Spring Rate Interactive Calculator Engineering Calculator

Torsion Spring Calculator — Torque and Deflection Engineering Calculator

Spring Interactive Calculator Engineering Calculator

Browse the FIRGELLI Engineering Library

Mechanisms Library

The complete reference of mechanical mechanisms — engineering analysis, formulas, components, and real-world applications.
Browse all mechanisms →
Engineering Calculators

1,300+ interactive calculators across 29 categories — torque, force, gear ratios, beam deflection, and more.
Browse all calculators →

About the Author

Robbie Dickson — Chief Engineer & Founder, FIRGELLI Automations

Robbie Dickson is the Chief Engineer and Founder of FIRGELLI Automations. He has spent 25 years designing motion systems — from linear actuators in industrial automation to drive trains in restored shop equipment. He keeps a 50 lb Little Giant Spring Hammer in his own shop and has rebuilt three of them, so the numbers in this article come out of measured behaviour, not just textbooks.

Wikipedia · Full Bio